NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
The Grain Auger: Archimedes' Screw Spun Fast in a Tube
Martin

Tạo bởi

Martin

27. tháng Chín 2026NO
2
0
0
0
0

The Grain Auger: Archimedes' Screw Spun Fast in a Tube

Archimedes' screw lifts water slowly by trapping it between turns of a spiral. Close the spiral in a tight tube and spin it fast, and it moves dry grain instead: the flights push the grain along and the tube keeps it from turning with them. The auger fills bins, empties combine tanks and loads trucks, at any angle from flat to steep, with nothing but a shaft and a motor. It is a sibling of the bucket elevator: the elevator lifts straight up in buckets and needs a tower; the auger lifts at a slant in a single tube and goes where it is carried. This rung works out an auger's theoretical delivery and why its fill factor must be measured, and builds a clear-tube auger to measure it at three angles.
Cơ bản
About 4 hours

Hướng dẫn

1

Delivery, fill factor and power

Đang tải sổ tay Jupyter…
2

The water sibling

The same spiral lifts water when turned slowly in an open trough. The embedded blueprint builds one; compare how each holds its load.
3

Build a clear-tube auger

3D-print screw flights 40 mm across with a 40 mm pitch, in 150 mm sections with an 8 mm bore, and thread them onto an 8 mm threaded rod locked with nuts. Slide the screw into a clear acrylic tube with a 42 mm bore. Cut an intake window at the bottom and a discharge hole at the top. Mount the tube on a plywood stand that can be set at 0, 20 and 40 degrees, with the rod running in skateboard bearings at each end. Drive the top end from a geared DC motor on an adjustable supply. Keep your fingers, hair and sleeves clear of the intake window while it turns.

Vật liệu cho bước này:

Ống acrylic (trong suốt)Ống acrylic (trong suốt)1 cái
Ty renTy ren1 cái
Vòng bi ván trượtVòng bi ván trượt2 cái
Tấm gỗ dánTấm gỗ dán1 cái
Động cơ một chiều có hộp sốĐộng cơ một chiều có hộp số1 cái
Đậu lăng khôĐậu lăng khô3 kilogram

Công cụ cần thiết:

Máy in 3D sợi nhựa (FDM)Máy in 3D sợi nhựa (FDM)
Sợi in PETGSợi in PETG
Nguồn điện một chiềuNguồn điện một chiều
Máy khoan pinMáy khoan pin
Bộ mũi khoanBộ mũi khoan
Mỏ lếtMỏ lết
Thước đo gócThước đo góc
Kính bảo hộ trong suốtKính bảo hộ trong suốt
4

Measure the fill factor

Keep the intake window buried in a tray of lentils. At each angle and at two motor speeds, run for 30 seconds, catch the discharge, weigh it, and read the shaft speed with the tachometer. Work out the theoretical delivery from the notebook's formula using your flight diameter, rod diameter and pitch, and the lentils' bulk density (weigh a measured jug full). The fill factor is measured delivery divided by theoretical. Tabulate it: it is highest flat and falls as the tube is tipped up, because more lentils slip back over the flights.

Công cụ cần thiết:

Máy đo tốc độ vòng quayMáy đo tốc độ vòng quay
Đồng hồ bấm giờĐồng hồ bấm giờ
Cân nhà bếp điện tửCân nhà bếp điện tử
Ca đongCa đong
XôXô
5

An auger that is not moving the grain

Grain auger faults, from the first to check.

Flow

Loading...
6

Context and honest limits

The screw conveyor is old; the portable farm auger in a tube is the form that moves most grain on farms today, from combine unloading augers to bin-filling augers. **Honest limits.** The notebook's theoretical delivery assumes a full tube moving one pitch per turn — no auger does this, which is why the bench test measures the fill factor. An auger damages some grain by rubbing, more at high speed and with fragile crops. And the exposed intake is one of the most common causes of serious injury on farms: guards stay on.

Vật liệu

6

Công cụ yêu cầu

13

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...