NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO

Toothed-Disk Potato Masher: Teeth Split It, Holes Take It
A perforated masher only pushes; firm pieces roll away from the holes.
George A. Anderson and Charles J. Baker of Albany, New York, received US 108,083, dated 11 October 1870, for a utensil for preparing potatoes and meat: a metal disk with several series of incising teeth and perforations placed alternate, the teeth's width radial; pressed down, "the incisors ... will enter the vegetables and split them at each point in contact, when the broken portions of the vegetables operated upon will rise up and pass through the openings."
This rung works out the teeth and open area, then prints the disk, fits a handle, and mashes potatoes.
Cơ bản
About 1 hour, plus printing
Hướng dẫn
1
1
Teeth and open area
Teeth and open area
Đang tải sổ tay Jupyter…
2
2
A perforated disk before it
A perforated disk before it
The embedded blueprint mashes through a perforated disk. Anderson and Baker put teeth between the holes to split the potato first.
3
3
Read US 108,083
Read US 108,083
"We prefer to have the said incisors c to have their width run in the direction of the radii of a circle, as shown in fig. 1, which would strengthen the rim, inclosing the outer series of perforations a with the rim inclosing the inner series of perforations a, and permit the metal of the disk A being made lighter."
4
4
Print the disk
Print the disk
Print the disk with its teeth and socket (/uploads/blueprints/toothed-disk-potato-masher-disk.stl) socket down, teeth up. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Vật liệu cho bước này:
Sợi in PETG1 cáiCông cụ cần thiết:
Máy in 3D sợi nhựa (FDM)5
5
Fit the handle
Fit the handle
Epoxy a 16 mm hardwood dowel 170 mm long into the socket.
Vật liệu cho bước này:
Chốt gỗ cứng1 cái
Keo epoxy hai thành phần1 cáiCông cụ cần thiết:
Cưa sắt
Thước cặp điện tử 6 inch6
6
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: an 84 mm disk with 8 inner and 14 outer radial incisors alternating with as many round holes, its socket and handle.
7
7
Mash firm potatoes
Mash firm potatoes
Boil 500 g of potatoes in their skins for about 25 minutes until a knife slides in; drain. Mash half with the toothed disk and time it to no lumps; compare with the yielding-disk masher if you built it.

Vật liệu cho bước này:
Khoai tây1 cái
Nước1 cáiCông cụ cần thiết:
Nồi quánh thành cao
Tô trộn thép không gỉ (lớn)
Đồng hồ bấm giờ8
8
Teeth that bend, holes that clog
Teeth that bend, holes that clog
Toothed-disk potato masher troubleshooting.
Flow
Loading...
9
9
History and honest limits
History and honest limits
**George A. Anderson** and **Charles J. Baker** of Albany, New York, received US 108,083, dated 11 October 1870. Two opposite sides of each perforation depend below the disk as the incisors; any suitable handle may be fixed by a socket, upright or at an angle. They named meat as well as potatoes.
**Honest limits.** A printed disk stands in for their metal one. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times are the result.
Vật liệu
5- 1 cáiTạm thời
- 1 cáiTạm thời
- Tạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
Công cụ yêu cầu
6- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
Tệp thiết kế
1Bản thiết kế này làm ra
Blueprint liên quan
Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc

Yielding-Disk Potato Masher: A Perforated Disk That Rocks to the Mash
bởi TheChef
THỰC PHẨM VÀ ĐỒ UỐNG
36
0
0
0
0
0

Wire-Coil Potato Masher: A Flat Spiral of Wire on Five Braces
bởi Forge
Gia công kim loại
23
0
0
0
0
0

Draining-Tube Potato Masher: Mash in a Tube, the Water Runs Out
bởi YourGrandma
THỰC PHẨM VÀ ĐỒ UỐNG
26
0
0
0
0
0
CC0 Phạm vi công cộng
Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.
Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.
