Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Belt-Driven Multiple Egg Beater: One Wheel Beats Three Bowls
English
Emma

Yenziwe ngu-

Emma

6. uMfumfu 2026SE
40
0
0
0
0

Belt-Driven Multiple Egg Beater: One Wheel Beats Three Bowls

A kitchen beating whites, yolks and batter needs several beaters going at once. John L. Nicolai of Chicago received US 23,814, dated 26 April 1859, for an egg beater: a grooved driving wheel turned by a handle belts a series of vertical arbors in one frame, each with a disk of flexible fingers of rubber or gutta-percha; turning, the fingers spread and sweep "through every nook and corner of the vessel," so several vessels are beaten at once. This rung works out the belt ratio and the fingers' spread, then prints the wheel, pulleys and disks and beats three bowls together.
Osezingeni eliphezulu
About 6 hours, plus printing

Imiyalelo

1

Ratio and finger spread

Ilayisha incwadi ye-Jupyter…
2

A belt drive before it

The embedded blueprint drives a pulley by a belt. Nicolai runs one belt per arbor in its own groove of a single wheel.
3

Read US 23,814

"By this motion and by the action of the substance in the vessels the fingers F spread out and a large quantity of the substance is agitated by the same at once, so that it takes but a very short time to reduce a quantity of eggs to froth or to mix a certain quantity of eggs with sugar, and as the fingers are flexible they diverge by being rotated with the disks and they adapt themselves to the shape of the vessel so that they actually sweep through every nook and corner of the vessel."
4

Print the wheel, pulleys and disks

Print the three-groove driving wheel, three pulleys and three finger disks. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.

Izinto zokwakha zalesi sinyathelo:

Ifilamenti ye-PETGIfilamenti ye-PETG1 ucezu

Amathuluzi adingekayo:

Iphrinta ye-3D yentambo (i-FDM)Iphrinta ye-3D yentambo (i-FDM)
5

Print the wheel

The wheel, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
6

Print the pulley

The pulley, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
7

Print the disk

The disk, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
8

Build the frame

Make a table frame of plywood 330 × 80 mm on four legs 240 mm high. Drill 5 mm holes for the wheel's shaft and three arbors 70 mm apart.

Izinto zokwakha zalesi sinyathelo:

Ishidi le-plywoodIshidi le-plywood1 ucezu
Ibhulokhi Lokhuni OluqinileIbhulokhi Lokhuni Oluqinile1 ucezu
Isikulufo sokhuni #8 x 1"Isikulufo sokhuni #8 x 1"1 ucezu

Amathuluzi adingekayo:

Isaha Se-CopingIsaha Se-Coping
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
IrulaIrula
9

Arbors and fingers

Cut three 200 mm arbors of 5 mm rod. Epoxy a pulley at each top, at the height of its own groove, and a disk at each foot. Push six 30 mm lengths of silicone tube into each disk's holes as fingers.

Izinto zokwakha zalesi sinyathelo:

Ubhamu Oluyindilinga Lwensimbi EthambileUbhamu Oluyindilinga Lwensimbi Ethambile1 ucezu
Ipayipi Le-siliconeIpayipi Le-silicone1 ucezu
I-epoxy Yezingxenye EzimbiliI-epoxy Yezingxenye Ezimbili1 ucezu

Amathuluzi adingekayo:

Isaha SensimbiIsaha Sensimbi
Isibambo SebhentshiIsibambo Sebhentshi
10

Belts and crank

Fit the wheel on its shaft with a crank screw near its rim. Loop an O-ring from each groove to its pulley, choosing sizes that are taut.

Izinto zokwakha zalesi sinyathelo:

Isethi Yezindandatho Ze-OIsethi Yezindandatho Ze-O1 ucezu
Izikulufu zomshiniIzikulufu zomshini1 ucezu
Inathi Yezinhlangothi EziyisithuphaInathi Yezinhlangothi Eziyisithupha1 ucezu

Amathuluzi adingekayo:

I-Caliper Yedijithali Yamayintshi Ayi-6I-Caliper Yedijithali Yamayintshi Ayi-6
Isipanela esilungisekayoIsipanela esilungisekayo
11

The patent drawing

US 23,814 drawing sheet, public domain (expired patent).
Isinyathelo 11 - Image 1
12

Beat three bowls

Set three bowls under the arbors with one egg white each. Turn the crank about once a second and time each bowl to stiff peaks.
Isinyathelo 12 - Image 1

Izinto zokwakha zalesi sinyathelo:

IqandaIqanda3 izicucu

Amathuluzi adingekayo:

Isitsha esikhulu sokuxuba sensimbi engagqwaliIsitsha esikhulu sokuxuba sensimbi engagqwali
Iwashi Lokumisa IsikhathiIwashi Lokumisa Isikhathi
13

Belts that slip, cross or fingers that fly off

Belt-driven multiple egg beater troubleshooting.

Flow

Loading...
14

History and honest limits

**John L. Nicolai** of Chicago, assignor to himself, S. E. Knott and R. F. Farrell, received US 23,814, dated 26 April 1859. The frame is wood or other material on legs; the disks may be flanged, plain sheet metal, or small cups; the arbors' ends pass through the disks and finish in a flattened fork that also mixes. For larger machines he would put a multiplying gear before the wheel; under steam power it is unnecessary. **Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. O-rings stand in for his endless belts, silicone tube for rubber or gutta-percha fingers. Your times are the result.

Izinto

11

Amathuluzi Adingekayo

12

Amafayela omklamo

3

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...