Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Oscillating-Pump Churn: A Half-Round Vane Pump Lifts the Cream Over and Strains It Back Through a Partition
Martin

Yenziwe ngu-

Martin

9. uLwezi 2026NO
10
0
0
0
0

Oscillating-Pump Churn: A Half-Round Vane Pump Lifts the Cream Over and Strains It Back Through a Partition

W. H. McClintock of Frankfort, Ohio, received US 24,223, dated 31 May 1859, for a churn that is a pump. A box is divided by a perforated partition into a cream chamber and a butter chamber. In the cream chamber a half-round pump has a vane swung back and forth by a lever: each stroke sucks cream up through a passage round the pump and flap valves into one side, and forces the other side's cream up through valves on top into a channel that runs into the butter chamber. The cream strains back through the partition and goes round again, chafed at every pass, until the butter is left in the butter chamber. Pumping water round the same way rinses the churn and washes the butter. This rung builds it in a pine box with a printed pump.
Osezingeni eliphezulu
About 1 day, plus printing

Imiyalelo

1

What one stroke moves

Ilayisha incwadi ye-Jupyter…
2

Cream thrown over a partition, before it

Patterson's fan threw cream over a partition to return under it. McClintock pumps it over and strains it back.
3

Read US 24,223

"The cream first expelled flows into the chamber C, and by reason of the continued suction of the piston is caused to strain through the perforated partition D, and enter the cream or milk chamber again ready to be again similarly circulated, minus a greater portion of its fatty matter, said fatty matter remaining in the chamber C."
4

Print the pump E

The pump body: half-round chamber a, passage b round it with its inlet below, ports for valves c c'. Print it upside down on its flat top. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Ifayela LomklamoSTLCC0 - Free
5

Print the vane f

The piston vane with its half-round hub. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Ifayela LomklamoSTLCC0 - Free
6

Box A and partition D

From 18 mm pine make a box 500 x 220 mm and 300 mm deep inside, with a lid and knob. Screw pairs of 10 mm strips down both side walls 300 mm from the left end as grooves, and slide in a 12 mm plywood partition D 212 mm high, drilled all over with 8 mm holes 20 mm apart, with a knob to lift it. Fit a PVC spigot low in the right end, in chamber C, as the opening j.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe lomphayiniIpulangwe lomphayini3 izicucu
Iglu LokhuniIglu Lokhuni1 ucezu
Izikulufu zokhuniIzikulufu zokhuni40 izicucu
Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Ishidi le-plywoodIshidi le-plywood1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu
Umpompi we-PVCUmpompi we-PVC1 ucezu
Isivalo Se-siliconeIsivalo Se-silicone1 ucezu

Amathuluzi adingekayo:

Isaha SesandlaIsaha Sesandla
Isaha Le-jigsawIsaha Le-jigsaw
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isethi yamasaha ezimboboIsethi yamasaha ezimbobo
Ama-clampAma-clamp
Iphepha LokugayaIphepha Lokugaya
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
Ithephu LokulinganisaIthephu Lokulinganisa
7

Pump E and top plate

Cut a 12 mm plywood top plate 290 x 220 mm to fill chamber B from the left end to the partition. Cut a half-round groove across its underside for the vane's hub, 37 mm wide, centred 150 mm from the left end, and drill two 20 mm eduction holes d d' 50 mm each side of it. Glue rubber-sheet flaps e e' 32 mm square over them on top, hinged on one edge with a screw. Glue rubber flaps c c' over the two ports inside the pump's chamber, hinged at the top so they open inward. Screw the pump body under the plate, seal the joint with silicone, and rest the plate on cleats 200 mm above the floor so it closes chamber B.

Izinto zokwakha zalesi sinyathelo:

Ifilamenti ye-PETGIfilamenti ye-PETG1 ucezu
Ishidi le-plywoodIshidi le-plywood1 ucezu
Ishidi lerabhaIshidi lerabha1 ucezu
Isivalo Se-siliconeIsivalo Se-silicone1 ucezu
Izikulufu zokhuniIzikulufu zokhuni12 izicucu
Ipulangwe lomphayiniIpulangwe lomphayini1 ucezu

Amathuluzi adingekayo:

Iphrinta ye-3D yentambo (i-FDM)Iphrinta ye-3D yentambo (i-FDM)
Isaha Le-jigsawIsaha Le-jigsaw
Isethi yamasaha ezimboboIsethi yamasaha ezimbobo
Ummese wemisebenziUmmese wemisebenzi
Ibhola ElingenantamboIbhola Elingenantambo
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
8

Vane f, lever g and channel F

Fix the vane on a 12 mm stainless rod with an M4 screw across, set it in the chamber with the hub in the plate's groove, and pass the rod out through the pump's end and the box's near wall. Fix a hardwood lever g 24 x 12 mm, 245 mm long, on the rod outside, standing up past the lid, with a 28 mm dowel handle on top. Fix a pine board above the top plate, sloping down from 258 mm high at the left end to 238 mm over the partition, to form channel F into C.

Izinto zokwakha zalesi sinyathelo:

Insimbi engagqwali eyindukwanaInsimbi engagqwali eyindukwana1 ucezu
Izikulufu zomshiniIzikulufu zomshini1 ucezu
Inati Yokukhiya EnenayiloniInati Yokukhiya Enenayiloni1 ucezu
Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu
Iglu LokhuniIglu Lokhuni1 ucezu
Ipulangwe lomphayiniIpulangwe lomphayini1 ucezu
Izikulufu zokhuniIzikulufu zokhuni8 izicucu

Amathuluzi adingekayo:

Isaha SensimbiIsaha Sensimbi
Isaha SesandlaIsaha Sesandla
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
9

The build in 3D

FreeCAD model of this build, the near half cut away: box A with partition D in its grooves, the pump body with passage b and its inlet, the vane, the top plate with flaps e e', flaps c c' at the ports, channel F's board and the spigot. It was checked at five vane angles from -60 to +60 degrees.
Ifayela LomklamoBLENDCC0 - Free
10

Churn

Pour about 8 litres of heavy cream at about 15 °C into chamber B through C (it strains through the partition), checked with the thermometer, and put the lid on. Swing the lever steadily back and forth about 60 degrees each way and time it: cream spurts into channel F, runs into C and strains back. When the butter has gathered in C, draw off the buttermilk at the spigot, pour cold water in and pump it round to rinse the churn and wash the butter, then lift the butter out, work in a pinch of salt and weigh it.

Izinto zokwakha zalesi sinyathelo:

Ukhilimu ojiyileUkhilimu ojiyile8 l
AmanziAmanzi1 ucezu
Usawoti Wolwandle OmkhuluUsawoti Wolwandle Omkhulu1 ucezu

Amathuluzi adingekayo:

Ithemomitha enenaliti eshiywa ngaphakathiIthemomitha enenaliti eshiywa ngaphakathi
Iwashi Lokumisa IsikhathiIwashi Lokumisa Isikhathi
Isikali Sedijithali SasekhishiniIsikali Sedijithali Sasekhishini
Isitsha esikhulu sokuxuba sensimbi engagqwaliIsitsha esikhulu sokuxuba sensimbi engagqwali
11

Troubleshooting

Pump churn troubleshooting.

Flow

Loading...
12

History and honest limits

**W. H. McClintock** of Frankfort, Ross County, Ohio, US 24,223, 31 May 1859, "Churn". He claimed the circularly vibrating suction and force pump with a churn having a perforated partition. He gave no sizes or materials: the box, the printed pump, the rubber flaps and every size are ours.

Izinto

16

Amathuluzi Adingekayo

16

Amafayela omklamo

3

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...