UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Twisted-Strip Egg Beater: Faces Beat and Edges Cut
A wire beater passes through the egg and leaves a wake without much froth.
James P. McLean and Philemon A. Morley of Brooklyn received US 28,760, dated 19 June 1860, for an egg beater of corrugated or twisted strips of tin turned inside a can by a large and a small cog gear set between the double heads of its lid: "by means of twisted or corrugated strips of metal the gelatin mass is beaten by the flat surfaces as well as being broken or cut by the sharp edges thereof."
This rung works out how much of a twisted face pushes, then prints the gears and a cage of twisted strips, builds the lid drive on a can, and times a beating.
Ophakathi
About 4 hours, plus printing
Imiyalelo
1
1
How a twisted face beats
How a twisted face beats
Ilayisha incwadi ye-Jupyter…
2
2
A geared wire beater before it
A geared wire beater before it
The embedded blueprint beats with bent wires. McLean and Morley use twisted strips with faces and edges.
3
3
Read US 28,760
Read US 28,760
"The superiority of our arrangement of egg beaters over those that are in common use, is that by means of twisted or corrugated strips of metal the gelatin mass is beaten by the flat surfaces as well as being broken or cut by the sharp edges thereof, hence the action is analogous to the motion produced by the hand and spoon, whereas an ordinary wire beater simply passes through the egg like the rudder of a boat, leaving a simple wake behind it without producing an immediate fomentation as is the case with our beater."
4
4
Print the gears and cage
Print the gears and cage
Print the 36-tooth gear, the 12-tooth gear and the cage of four twisted strips. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Izinto zokwakha zalesi sinyathelo:
Ifilamenti ye-PETG1 ucezuAmathuluzi adingekayo:
Iphrinta ye-3D yentambo (i-FDM)5
5
Print the 36-tooth gear
Print the 36-tooth gear
The 36-tooth gear, printed as step 4 describes.
6
6
Print the 12-tooth gear
Print the 12-tooth gear
The 12-tooth gear, printed as step 4 describes.
7
7
Print the cage
8
8
Make the double lid
Make the double lid
Cut two plywood disks to the can's mouth. Space them 20 mm apart on three M5 screws with nuts, and drill both for the crank shaft and the cage shaft 48 mm apart.
Izinto zokwakha zalesi sinyathelo:
Ishidi le-plywood1 ucezu
Izikulufu zomshini1 ucezu
Inathi Yezinhlangothi Eziyisithupha1 ucezu
Iwasha Eliyisicaba1 ucezuAmathuluzi adingekayo:
Isaha Se-Coping
Ibhola Elingenantambo
Iqoqo Lamakhanda Ebhola
Isipanela esilungisekayo
I-Caliper Yedijithali Yamayintshi Ayi-69
9
Fit the shafts and gears
Fit the shafts and gears
Epoxy the large gear on a crank shaft of 5 mm rod with a bent handle, and the small gear on the cage shaft, both between the heads. Epoxy the cage on the cage shaft's lower end.
Izinto zokwakha zalesi sinyathelo:
Ubhamu Oluyindilinga Lwensimbi Ethambile1 ucezu
I-epoxy Yezingxenye Ezimbili1 ucezuAmathuluzi adingekayo:
Isaha Sensimbi
Isibambo Sebhentshi
Udlawu Lomlomo Oyisicaba10
10
The patent drawing
The patent drawing
US 28,760 drawing sheet, public domain (expired patent).
11
11
Beat egg whites
Beat egg whites
Put two egg whites in the can, fit the lid, and crank about once a second; time to stiff peaks.
Izinto zokwakha zalesi sinyathelo:
Ithini1 ucezu
Iqanda2 izicucuAmathuluzi adingekayo:
Iwashi Lokumisa Isikhathi12
12
Gears that skip, a cage that scrapes
Gears that skip, a cage that scrapes
Twisted-strip egg beater troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**James P. McLean** and **Philemon A. Morley** of Brooklyn, assignors to P. A. Morley, received US 28,760, dated 19 June 1860. Their Fig. 2, for bakers, puts the strips on a vertical water-tight cylinder turning round a stationary handle, driven by a hand wheel whose rubber band grips the cylinder's grater-like funnel top instead of cog wheels. They claimed the twisted beaters in combination with the cylinder.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Printed strips and plywood heads stand in for tin. Your times are the result.
Izinto
9- 1 ucezuIsibambeli
- 1 ucezuIsibambeli
- 1 ucezuIsibambeli
- Isibambeli
- 1 ucezuIsibambeli
- Isibambeli
- 1 ucezuIsibambeli
- 1 ucezuIsibambeli
- 2 izicucuIsibambeli
Amathuluzi Adingekayo
10- Isibambeli
- Isibambeli
- 1 vendor sell this, none ship to you yetIsibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
Amafayela omklamo
3Le blueprint yenza
Ama-blueprint ahlobene
Lama-blueprint abelana ngolwazi — amasu, izinto noma izimiso
CC0 Isizinda Somphakathi
Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.
Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.