Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

60-Mesh and 80-Mesh Sieves: U.S. Standard Sieves No. 60 and No. 80 (Bureau of Standards, 1924)
Two standard testing sieves made the same way; only the wire and the opening change with the sieve number. Plain-woven brass or bronze wire cloth is soldered smoothly into a round frame about 20 cm (8 in) across.
No. 60 has 0.250 mm openings (the 60-mesh sieve); No. 80 has 0.177 mm openings (the 80-mesh sieve). The finer the cloth, the finer the grains that pass.
Source: Bureau of Standards, Letter Circular 74, Standard Specifications for Sieves (revised 1924). Unknown: the frame metal and the weaving. Picture: the Bureau's table.
Intermediário
Unknown
Instruções
1
1
Choose the sieve number
Choose the sieve number
The sieve number sets the wire and the opening (Bureau of Standards table, 1924):
No. 60: opening 0.250 mm (0.0098 in), wire 0.162 mm (0.0064 in).
No. 80: opening 0.177 mm (0.0070 in), wire 0.119 mm (0.0047 in).
The opening is the clear space between adjacent wires. No. 60 passes grains under 0.250 mm; No. 80 passes grains under 0.177 mm.
2
2
Weave the wire cloth
Weave the wire cloth
Weave plain (not twilled) cloth from brass, bronze or other suitable wire of the diameter for your sieve number, spacing the wires so the opening is as in the table each way. Ours: bronze wire. Not given: how it is woven.
Materiais para este passo:
Arame de bronze1 warp and shoot wiresFerramentas necessárias:
Tear de rede metálica3
3
Make the frame
Make the frame
Make a circular frame about 20 cm (8 in) across, with about 5 cm (2 in), or 2.5 cm (1 in), between its top and the cloth. Ours: brass strip. Not given: the frame metal.
Materiais para este passo:
Tira de latão1 frameFerramentas necessárias:
Tesoura de chapa
Ferro de soldar4
4
Mount the cloth
Mount the cloth
Mount the cloth on the frame without distorting it. Fill the joint between cloth and frame smoothly with solder, so the material being sieved cannot catch in it.
Materiais para este passo:
Solda de estanho-chumbo1 joint
Fluxo1 jointFerramentas necessárias:
Ferro de soldar5
5
Check it against the tolerances
Check it against the tolerances
Measure the warp and shoot wires separately. For both numbers the average opening must be within ±6 % of the table, the average wire diameter within −15 to +35 %, and no opening may exceed the table opening by more than 40 %. Reject a sieve with punctures, loose or wavy cloth, poor soldering, or too many large openings.
Ferramentas necessárias:
Micrómetro
LupaMateriais
4- 1 warp and shoot wiresReferência
- 1 frameReferência
- 1 jointReferência
- 1 jointReferência
Ferramentas necessárias
5- Referência
- Referência
- 2 vendors sell this, none ship to you yetReferência
- Referência
- Referência
Materiais de Blueprints conectados

10% de atribuição
120-Mesh Sieve: U.S. Standard Sieve No. 120 (Bureau of Standards, 1924)
por Tex
Física
7
0
0
0
1
0

10% de atribuição
Tin Bronze Ingots, Wire and Rod
por Forge
Trabalho em Metal
53
0
0
0
2
0

10% de atribuição
Brass Sheet, Strip and Rod from an Ingot
por Forge
Trabalho em Metal
38
0
0
0
2
0

Perigoso
10% de atribuição
Making Tin-Lead Solder — The Ancient Alloy That Joins Metals Without a Forge
por Peter
Trabalho em Metal
60
0
0
0
3
0
Este projeto faz
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

