Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Bellows Rocking-Dasher Churn: A Hand Bellows Blows Air Down a Knee Nozzle Into the Cream and Rocks a Paddle Dasher Beside It
Buttercup

Criado por

Buttercup

11. novembro 2026IE
8
0
0
0
0

Bellows Rocking-Dasher Churn: A Hand Bellows Blows Air Down a Knee Nozzle Into the Cream and Rocks a Paddle Dasher Beside It

Charles T. Anderson of Hyattstown, Maryland, received US 32,553, dated 18 June 1861, for a churn worked by an ordinary bellows lying on a box beside the cream. Pumping its handle drives air down a knee-shaped nozzle to holes near the bottom of the pail, under a disk on legs; at the same time two cords over a roller on the bellows rock a lever at its nose, which through a link and crank swings a paddle dasher back and forth beside the nozzle. An adjustable hole on the bellows' top sets how much air goes in; closed, the dasher churns alone. The patent gives no sizes; every size here is ours.
Avançado
About 3 days

Instruções

1

Air for the cream

A carregar o notebook Jupyter…
2

A bellows blowing air through the cream, years before

The tempered-air churn uses the bellows alone. Anderson's bellows also rocks a dasher by cords and a lever.
3

Read US 32,553

"The vessel being filled with cream, an up and down or vibratory movement is given to the upper portion of the bellows by means of the handle and a current of air thereby forced through the nozzle of the bellows into the cream through the apertures of the lower end of the nozzle. At the same time a vibrating motion is imparted to the dasher."
4

Box C, platform S, bars B and bellows A

Make a hardwood box C 520 x 360 mm and 450 high from 20 mm boards, and screw a platform S 380 x 340 x 30 mm to the ground at one end of it. Screw two hardwood bars B 40 x 20 mm across its top, 280 mm apart. Lay a hand bellows about 460 mm long on them, its nozzle toward the platform, and screw its bottom board to the bars. Bore a 30 mm hole in its top board as the aperture b and screw over it a hardwood slide in guides, to open it wide, part way or shut. Bore a 40 mm hole in the bottom board near its nose and glue a leather flap over it inside, hinged at one edge, as the valve that lets air in as the bellows opens. Screw two hardwood cross pieces D 200 x 30 mm on the top board and a hardwood handle E 400 mm long to them, reaching back.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei4 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira40 peças
FoleFole1 peça
CouroCouro1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
5

Print the knee elbow

The elbow joining the nozzle's two tubes: two 22.4 mm sockets at right angles round a 17 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Nozzle G, disk I and the pail H

Cut a 22 mm stainless tube into a short end f 300 mm long and a long end 460 mm long and join them at right angles in the printed elbow with food-safe silicone, as the knee nozzle G; drill six 7 mm holes round the long end 25 mm above its foot. Fit the short end into the bellows' nozzle, sealed with leather. Cut an HDPE disk I 180 mm across, bore it 22.6 mm 80 mm from its centre for the tube, four 24 mm apertures h round its centre, and a socket boss at its centre; screw three hardwood legs g 60 mm long under it. Slide it on the tube so the tube's foot and the legs stand on the floor of a 20-litre food-grade pail H set on the platform. Cover the pail with butter muslin.

Materiais para este passo:

Tubo de aço inoxidávelTubo de aço inoxidável1 peça
Filamento PETGFilamento PETG1 peça
Vedante de siliconeVedante de silicone1 peça
CouroCouro1 peça
Chapa de PEADChapa de PEAD1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Parafusos para madeiraParafusos para madeira3 peças
Balde de 20 litrosBalde de 20 litros1 peça
Pano de queijo de algodãoPano de queijo de algodão1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Serra tico-ticoSerra tico-tico
BússolaBússola
7

Staff J, dasher M, yoke, crank K and link L

Turn a hardwood staff J 20 mm across and 375 mm long, its foot to fit the disk's socket. Screw a hardwood paddle M 120 x 200 x 12 mm across it, its foot 25 mm above the disk. Fix a yoke of mild steel flat bar to the tube 340 mm above the pail's floor, with a ring round the staff's top. Pin a crank K of flat bar, 60 mm throw, on the staff's top, and join it with a flat bar link L to one end of the lever F.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Parafusos para madeiraParafusos para madeira4 peças
Barra chata de aço macioBarra chata de aço macio1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados2 peças
ContrapinoContrapino2 peças

Ferramentas necessárias:

Torno de madeiraTorno de madeira
Serra de mesaSerra de mesa
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
8

Print the forked bracket O

The forked bracket on the bellows' top board: 160 mm long, a 40 x 34 mm fork to slide on the post and a 30 x 24 slot for the roller P. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
9

Lever F, post N, bracket O, roller P and cords Q, R

Cut a hardwood lever F 300 x 30 x 15 mm and pivot it at its middle on an M10 bolt e upright in the bellows' nose block, with a wing nut. Screw a pedestal block to the box's back end and stand a hardwood post N 30 mm square, 380 tall, in it behind the bellows. Screw the bracket O to the top board's back end so its fork slides on the post, and pin a hardwood roller P 18 mm across in its slot. Tie a cord Q from the post's top, under the roller, to one end of the lever, and a cord R from the pedestal, over the roller, to the other end, both just taut with the bellows half open.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados1 peça
Porca borboletaPorca borboleta1 peça
Anilha planaAnilha plana2 peças
Filamento PETGFilamento PETG1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
CordelCordel1 peça
Parafusos para madeiraParafusos para madeira8 peças

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Chave inglesa ajustávelChave inglesa ajustável
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
10

The build in 3D

FreeCAD model of this build, the pail cut open: the box and platform, the bellows with its slide, cross pieces and handle, the knee nozzle down to the holed foot under the disk on its legs, the staff with its paddle and yoke, the lever on its bolt, the link, and the post with the forked bracket, roller and cords.
Arquivo de designBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the pail and cover it with the muslin. Work the handle up and down steadily, timing it: the bellows blows air out under the cream and the paddle rocks. Open or close the slide on the bellows' top to give more or less air. When the butter comes, unhook the link from the crank, draw the nozzle out of the bellows and lift the pail away; turn the disk on the tube until the staff's foot clears it and lift the dasher out. Take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater8 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
12

Troubleshooting

Bellows churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Charles T. Anderson** of Hyattstown, Montgomery County, Maryland, US 32,553, 18 June 1861, "Churn". He claimed the pivoted reciprocating dasher M with the bellows A and vertical nozzle G, and the nozzle G, detachable dasher M and eccentrically pivoted disk I together. His bellows was "of ordinary construction"; ours is a bought or made hand bellows with the patent's top aperture, valve and nozzle added. His vessel could be a firkin, pail, can or box. The patent gives no sizes; every size here is ours.

Materiais

21

Ferramentas necessárias

19

Ficheiros de design

3

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...