Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Three-Crank Churn: One Dasher Strokes Up and Down While Two Side Dashers Swing In and Out
Buttercup

Criado por

Buttercup

11. novembro 2026IE
9
0
0
0
0

Three-Crank Churn: One Dasher Strokes Up and Down While Two Side Dashers Swing In and Out

Abel Austin of Altona, Illinois, received US 25,553, dated 27 September 1859, for a churn. A shaft bent into three cranks works three dashers: the middle one strokes straight up and down between guides on the box's ends, and two side dashers on levers pivoted in the lid swing sideways, coming together as the middle one rises and parting as it falls. The shaft and dashers lift out together, and the side dashers also press the buttermilk out of the butter. The patent gives no sizes; every size here is ours.
Intermediário
About 3 days, plus printing

Instruções

1

Up and down in the middle, in and out at the sides

A carregar o notebook Jupyter…
2

Dashers on a bent crank shaft, two weeks before

Gilpatrick's two dashers both stroke up and down. Austin keeps one up-and-down dasher and adds two that swing sideways.
3

Read US 25,553

"My invention uses the old principle of the up and down dasher and for the purpose the greatest possible effective motion to the milk in a breaking or dashing manner, the side dashers having a lateral stroke are added, they are also designed to gather the butter after it is churned and press and work out the buttermilk."
4

Print the middle link

The link from the middle crank to D's handle: 120 mm between its two 12.6 mm eyes, 22 x 10 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
5

Print the side links

The links from the side cranks to the side levers: 167 mm between their eyes, 22 x 10 mm. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Box, stays N and posts

From 20 mm hardwood make a box 500 mm long inside, 300 mm wide at the floor and 360 mm at the top, 380 mm deep, with square ends and the sides sloping out. Carry each end up as a post 80 mm wide to 650 mm above the floor, cut a 13 mm slot down its middle to 600 mm, and hinge a hardwood cap over the slot, held by a hook and eye. Glue two strips 20 x 20 mm up the inside of each end, 64 mm apart, as the stays N. Fill the box with water overnight so it swells tight, then empty it.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei4 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira40 peças
Dobradiça de livro para móvelDobradiça de livro para móvel2 peças
Colchete (macho e fêmea)Colchete (macho e fêmea)2 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
SerroteSerrote
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Esquadro fixoEsquadro fixo
Fita métricaFita métrica
ÁguaÁgua
Conjunto de chaves de fendasConjunto de chaves de fendas
7

Lid F, F' and pivots H

Cut the lid to lie on the box between the posts, in two parts: F, 360 mm long from one end, and F' for the rest, with a turn button K on F to hold F'. In F cut a slot P 40 mm square in the middle, and two slots 30 x 50 mm each side, 40 mm either side of the middle and 133 mm out from it, and bore each across for a 10 mm stainless pin: the pivots H.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Parafusos para madeiraParafusos para madeira2 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Formão de samblagemFormão de samblagem
Maço de madeiraMaço de madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
8

Shaft a with three cranks

Bend 12 mm stainless rod about 900 mm long, heating each bend red with the torch, into three cranks side by side in the middle: a middle crank of 40 mm throw, and a 25 mm crank each side of it, those two pointing opposite ways and both at right angles to the middle one. Make each crank pin 40 mm long. Leave 220 mm of straight shaft one side and 250 mm the other, and fit a hardwood crank handle on the longer end.

Materiais para este passo:

Varão de aço inoxidávelVarão de aço inoxidável1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Maçarico a propanoMaçarico a propano
Torno de bancadaTorno de bancada
MarteloMartelo
Luvas resistentes ao calorLuvas resistentes ao calor
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
9

Dashers D and E, E

Make D a hardwood plate 498 x 60 x 20 mm, to slide between the stays, on a handle D' 30 mm square and 402 mm long, bored 12.6 mm 12 mm from its top. Make each side lever e 30 mm square and 514 mm long, bored 12.6 mm at its top and 10.4 mm 220 mm below it for the pivot, and screw a board E 440 x 120 x 20 mm across its foot. Set the lid on, D's handle through P and each lever in its slot on its pivot pin. Put the shaft in the posts' slots and close the caps, then join each crank to its handle with its printed link, fixed with washers and split pins.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira8 peças
Anilha planaAnilha plana6 peças
ContrapinoContrapino6 peças
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
LixaLixa
Fita métricaFita métrica
10

The build in 3D

FreeCAD model of this build, one side and the loose half of the lid left off: the box with its stays and posts, the shaft with its three cranks, the links, the middle dasher in its stays and the two side dashers on their pivots. The crank was turned through 24 positions.
Arquivo de designBLENDCC0 - Free
11

Churn, then press

Pour about 20 litres of heavy cream at about 15 °C into the box, checked with the thermometer, put F' on and turn the button. Turn the crank steadily, timing it; F' can come off to look. When the butter comes, unhook the caps, slip the middle link off its crank, lift out the shaft with the side dashers and lid F, and pour off the buttermilk. Put the shaft and side dashers back, add cold water, and turn the crank to work the butter and press the buttermilk out with the side dashers. Lift out the butter, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater20 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
12

Troubleshooting

Three-crank churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Abel Austin** of Altona, Knox County, Illinois, US 25,553, 27 September 1859, "Churn". He disclaimed the shaft with cranks and the dashers with handles on their own, and claimed their arrangement with the links, springs, bearing box i, spring g and lid F F'. The patent gives no sizes; every size here is ours. His springs c on the links and spring g on the bearing boxes are here split pins and a hook and eye.

Materiais

13

Ferramentas necessárias

24

Ficheiros de design

3

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...