Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Hinged-Float Double-Dasher Churn: Floats That Close Going Down and Fall Open Coming Up
Buttercup

Criado por

Buttercup

10. novembro 2026IE
6
0
0
0
0

Hinged-Float Double-Dasher Churn: Floats That Close Going Down and Fall Open Coming Up

William Campbell of Waterloo, Pennsylvania, received US 25,383, dated 13 September 1859, for a dasher head made of perforated floats hinged in a frame. A lever on top of a removable partition works two dashers, one in each half of a box; as one goes down the other comes up. Going down, the cream presses the floats shut and the head fills the box's end; coming up, they fall open so the cream does not spatter over the top. Moving one shaft nearer the pivot shortens its stroke, and the butter gathers round it. Campbell gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

Long stroke, short stroke

A carregar o notebook Jupyter…
2

A lever working two dashers, before it

Campbell knew a lever with two dashers was not new. What he added were the hinged, perforated floats.
3

Read US 25,383

"The descending dasher has its floats F, closed by the resistance of the cream. As the dasher head fills the end of the box, the cream is partly driven downward into the opposite end of the churn. Some of the milk rises through the perforations in the descending dasher; then upon the return stroke of lever C the milk takes the opposite course."
4

Box A with legs

From 20 mm hardwood cut a bottom 540 x 290 mm, two sides 540 x 400 mm and two ends 250 x 400 mm. In each side's inner face, in the middle, cut a groove 19 mm wide and 6 mm deep from top to bottom for the partition. Glue and screw the ends between the sides and the box onto the bottom. Drill an 18 mm hole low in each end for the buttermilk and shape two tapered hardwood plugs to fit. Screw four legs of 70 mm timber, 300 mm long, under the corners. Fill the box with water overnight so it swells tight, then empty it.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei3 peças
Madeira macia de 70x70 mmMadeira macia de 70x70 mm1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira30 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
SerroteSerrote
FormõesFormões
Berbequim sem fiosBerbequim sem fios
Conjunto de brocas de páConjunto de brocas de pá
Sargento de barraSargento de barra
Esquadro fixoEsquadro fixo
Fita métricaFita métrica
ÁguaÁgua
5

Partition B

Cut an 18 mm hardwood partition 261 x 400 mm to slide down the grooves, with a post 60 mm wide rising 170 mm above it. Drill four rows of six 16 mm holes across its lower end, as Fig. 3 draws, the lowest row 25 mm up. Saw a 24 mm slot 50 mm deep in the top of the post and bore a 12.6 mm hole across it 150 mm above the box for the lever's pin.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça

Ferramentas necessárias:

SerroteSerrote
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Conjunto de brocas de páConjunto de brocas de pá
Jogo de brocasJogo de brocas
FormõesFormões
6

Dasher heads with hinged floats F

For each head make a hardwood frame 230 x 230 mm of 12 mm strips with a 12 mm bar across the middle and a block on top of the bar for the shaft's pin. Cut two floats 95 x 204 mm from 10 mm hardwood and drill each with three rows of five 14 mm holes. Hinge each float on the middle bar with stainless wire through drilled knuckles so its outer edge can fall open and rises against the frame's top lip when the head goes down.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Arame de aço inoxidávelArame de aço inoxidável1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira8 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
SerroteSerrote
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Limas (lima de mão)Limas (lima de mão)
LixaLixa
7

Lever C, shafts D and E, cover G

Make the lever from hardwood 40 x 22 mm, 1,000 mm long, with its pivot hole 300 mm from the short end, a hole for shaft D 230 mm from the pivot on the long arm, and on the short arm a hole for E 230 mm out and a second hole c 150 mm out. Pin it into the post's slot with a 12 mm stainless rod. Cut shafts D and E from 22 mm dowel, 450 mm between pin centres, slot their ends and pin them to the lever and to the heads' blocks with 6 mm stainless bolts. Make cover G for the D end from 15 mm hardwood with a 30 mm slot for shaft D.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados4 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon4 peças
Anilha planaAnilha plana4 peças

Ferramentas necessárias:

SerroteSerrote
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Chave inglesa ajustávelChave inglesa ajustável
Fita métricaFita métrica
8

The build in 3D

FreeCAD model of this build, one side cut away: the box on its legs, the partition perforated low with its post, the lever on its pin, shafts D and E down to their heads, each head a frame with two perforated floats, the cover over the D end, and the plugs. Checked over 12 degrees each way with E in either hole.
Arquivo de designBLENDCC0 - Free
9

Churn, then gather

Plug both ends and pour about 15 litres of heavy cream at about 15 °C into the box, checked with the thermometer. Rock the lever steadily, timing it. When butter begins to form, unpin shaft E and pin it in hole c, and go on rocking: the butter gathers round E and rises above its head in the open end. Lift it out, draw the buttermilk off at the plugs, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it. To clean, pour in hot water, give a few strokes and lift the dashers and partition out to dry.

Materiais para este passo:

Natas para baterNatas para bater15 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
10

Troubleshooting

Hinged-float churn troubleshooting.

Flow

Loading...
11

History and honest limits

**William Campbell** of Waterloo, Juniata County, Pennsylvania, US 25,383, 13 September 1859, "Churn". He claimed the perforated and hinged floats F as an improvement in dasher heads. He knew divided boxes and a lever working two dashers were not new, and that perforated dashers hinged to a central partition had been used in swinging churns. He gives no sizes, so every size here is ours. He set the shafts obliquely into the heads; ours are pinned at both ends so the heads stay level between the walls.

Materiais

13

Ferramentas necessárias

19

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...