Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Reed Basket on a Wood Bottom: 24 Spokes, Rolled Edge, Triple Weave and Break-Down Border (Boy Mechanic, 1915)
Woody

Criado por

Woody

13. novembro 2026NO
7
0
0
0
0

Reed Basket on a Wood Bottom: 24 Spokes, Rolled Edge, Triple Weave and Break-Down Border (Boy Mechanic, 1915)

The first lesson of Chas. M. Miller's reed-furniture series in The Boy Mechanic, Book 2 (1915): a basket 5 in across and 3 in high, woven on a bored basswood bottom. The spoke ends are turned into a roll that hides the wooden edge, the side is triple-woven, and the top is finished with a break-down border.
Iniciante
About 3 hours

Instruções

1

His sizes, and the spoke spacing

A carregar o notebook Jupyter…
2

Read The Boy Mechanic, Book 2

"The center is the most difficult part of the basket making, and it is best to begin with wood bottoms." The reeds placed vertically are called spokes, the horizontal ones weavers.
3

Make the bottom

On a board about 6 in square, 1/4 in thick (basswood is best, pine or cedar will do), draw the diagonals and two circles from their crossing, 5 in and 4-3/4 in across. Step off 24 points on the inner circle with the compass set about 5/8 in apart, adjusting until they come out even. Bore 1/8 in holes just inside the inner circle at the points, then saw out the 5 in circle (bore first, or the disk may split).

Materiais para este passo:

Tábua de pinhoTábua de pinho1 peça

Ferramentas necessárias:

BússolaBússola
LápisLápis
Berbequim de mãoBerbequim de mão
Serra de recortesSerra de recortes
4

Set the spokes and roll the edge

Push dry No. 4 reed spokes through the holes, about 5-1/2 in projecting below. Soak bottom and spokes about 15 minutes. Bend each spoke below the bottom down behind the two nearest spokes and out between the third and fourth; force the last two under the first two, making a pinwheel. Then bend them up across the edge of the wood, in front of three spokes and behind the fourth, inserting a short spoke about 4 in long in front of each first so the doubles cover the edge; press them flat and trim any that are too long.

Materiais para este passo:

RotimRotim1 peça

Ferramentas necessárias:

Balde de 20 litrosBalde de 20 litros
Faca para couroFaca para couro
FormõesFormões
5

Triple-weave the side

Put in three soaked No. 3 reed weavers between spokes A-B, B-C and C-D. Each time take the weaver farthest behind in front of the two nearest spokes, behind the third and out in front of the next two. Use weavers no longer than 8 ft; when one runs out, press it back a little and push a new reed in about 1-1/2 in. Press every throw down, and weave to 3 in high.

Materiais para este passo:

RotimRotim1 peça

Ferramentas necessárias:

Balde de 20 litrosBalde de 20 litros
Faca para couroFaca para couro
6

Make the border

Break-down-tight border: bend spoke A behind B and out between B and C, B behind C, and so on to E; then lay the end of A over B to E, in front of F, behind G and out between G and H, and bring F down behind A's end; continue round, leaving the first ends loose so the last spokes can be worked under them. Or use the simple break-down: each spoke behind the next, in front of the one after, and behind the next, not out again.

Ferramentas necessárias:

Faca para couroFaca para couro
7

Finish

When dry, cut the long ends off close with a knife, without cutting a weaver. Singe off hairy fibres over a flame that will not smut. Do not leave reeds in water longer than needed, as they turn dark; dampen them often while weaving so they pack down closer. He also mentions bleaching with chloride of lime in water set in sunlight, but warns too much gives a whitish look; it is not part of this blueprint.

Ferramentas necessárias:

Faca para couroFaca para couro
Maçarico a propanoMaçarico a propano
8

Troubleshooting

Reed basket troubleshooting.

Flow

Loading...
9

History and honest limits

From "Reed Furniture: A Reed Basket" by Chas. M. Miller, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 257-260). Reed sizes are his trade numbers (No. 3, No. 4). Bleaching is described in his text but left out here. The tools and metric figures are ours.

Materiais

2
  • Referência
  • 1 peça
    Referência

Ferramentas necessárias

8

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...