Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Ice-Chamber Air Churn: The Hollow Dasher Pumps the Same Air Round Through Ice and Cream
Buttercup

Criado por

Buttercup

9. novembro 2026IE
6
0
0
0
0

Ice-Chamber Air Churn: The Hollow Dasher Pumps the Same Air Round Through Ice and Cream

James H. Bump of Morris, New York, received US 21,871, dated 26 October 1858, for a churn with an ice chamber on its lid. A hollow dasher with a valve draws air from the ice chamber on every up stroke and forces it into the cream on every down stroke; the air pushed up out of the case returns through a tube into the ice chamber, so the same air goes round, cooled each time. This rung builds it in a 20-litre bucket with printed parts and a lever.
Intermediário
About 5 hours, plus printing

Instruções

1

Air, depth and lever

A carregar o notebook Jupyter…
2

Air through a hollow dasher, before it

Marcell blew room air down a hollow dasher shaft. Bump draws it from an ice chamber and sends it round again.
3

Read US 21,871

"At every upward movement of the staff F, the air from the chamber C, rushes down within the staff F, into the chamber d ... and as the dasher descends the valve e, closes and the air within will be forced into the cream j, and at the same time the air in the case above the cream will be compressed by the rising of the cream j ... and said air will pass up the space f, into the chamber C".
4

Print the tube E

Tube E, 40 mm across and 155 mm long, with its flange under lid B. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Arquivo de designSTLCC0 - Free
5

Print the clamp ring

The ring that clamps tube E's flange, lid B and the chamber floor together. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Arquivo de designSTLCC0 - Free
6

Print the box a

Upper box a, 110 mm tall, with the staff's top guide. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Arquivo de designSTLCC0 - Free
7

Print the box a'

Lower box a', with the four notches that do the work of Bump's grooves. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Arquivo de designSTLCC0 - Free
8

Print the dasher G

The bell dasher, 160 mm across, with chamber d open below. It needs a 160 mm bed; print it top down. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Arquivo de designSTLCC0 - Free
9

Print the flap e

The valve flap with its two hinge knuckles. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Arquivo de designSTLCC0 - Free
10

Print the staff head

The block that closes the staff's top and takes pin h. PETG, 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Arquivo de designSTLCC0 - Free
11

Lid, tube and ice chamber

Use a food-grade 20-litre bucket and its lid (lid B), and a round food container 200 mm across and 130 mm deep as chamber C, its own lid as lid D. Cut a 40 mm hole in the middle of lid B and of the container's floor. Push tube E up from under lid B, set the container on the lid and the clamp ring over the tube, and fix them with four M4 screws and lock nuts. Cut a 30 mm hole in the middle of lid D.

Materiais para este passo:

Filamento PETGFilamento PETG1 peça
Balde de 20 litrosBalde de 20 litros1 peça
Recipiente de armazenamento de grau alimentarRecipiente de armazenamento de grau alimentar1 peça
Parafusos de máquinaParafusos de máquina4 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon4 peças

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Conjunto de serras-copoConjunto de serras-copo
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
Chave inglesa ajustávelChave inglesa ajustável
12

Boxes and hollow staff

Bolt box a on top of lid D and box a' under it through their flanges, three M4 screws, the notches of a' against the lid. Cut the stainless tube (16 mm, 1 mm wall) to 549 mm. Drill two 5 mm holes c straight through it, crossed, 389 mm from its foot, and a 4.4 mm hole across it 6 mm and 534 mm from its foot for the cross screws.

Materiais para este passo:

Parafusos de máquinaParafusos de máquina3 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon3 peças
Tubo de aço inoxidávelTubo de aço inoxidável1 peça

Ferramentas necessárias:

Corta-tubosCorta-tubos
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Limas (lima de mão)Limas (lima de mão)
Conjunto de chaves de fendasConjunto de chaves de fendas
13

Dasher and valve

Hang the flap e on the lug in the dasher's chamber with an M3 screw and lock nut so it covers the air hole from below and swings down freely. Push the staff's foot 12 mm into the dasher's top and fix it with an M4 screw across.

Materiais para este passo:

Parafusos de máquinaParafusos de máquina2 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon2 peças

Ferramentas necessárias:

Conjunto de chaves de fendasConjunto de chaves de fendas
Chave inglesa ajustávelChave inglesa ajustável
14

Upright and lever

Cut a hardwood foot 90 x 34 x 30 mm and bolt it to lid B 120 mm from the middle, with two M6 bolts through a hardwood backing strip under the lid. Screw a hardwood upright 30 x 45 mm, 337 mm tall, on it. Cut two lever strips 30 x 12 mm, 480 mm long; drill each 20 mm from one end for pin g and cut a 6.5 mm slot from 110 to 135 mm past it for pin h. Lower the staff through tube E and the boxes, push on the staff head with an M4 screw across, and bolt the strips either side of the upright (pin g) and of the head (pin h) with M6 bolts, washers and lock nuts.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados4 peças
Anilha planaAnilha plana8 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon5 peças
Parafuso para madeira n.º 8 x 1"Parafuso para madeira n.º 8 x 1"4 peças
Parafusos de máquinaParafusos de máquina1 peça

Ferramentas necessárias:

SerroteSerrote
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Limas (lima de mão)Limas (lima de mão)
LixaLixa
Chave inglesa ajustávelChave inglesa ajustável
Fita métricaFita métrica
15

The build in 3D

FreeCAD model of this build at mid stroke, the near quarter of the bucket, chamber and boxes cut away: lid B with tube E, chamber C and lid D, boxes a and a', the hollow staff with its holes c, the bell dasher with flap e, the upright and the forked lever.
Arquivo de designBLENDCC0 - Free
16

Churn

Pour 8 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer. Fit lid B with the dasher in place, fill chamber C with crushed ice round tube E and close lid D. Work the lever up and down steadily, the full 100 mm stroke, and time it. When the butter comes, lift the lid out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater8 l
Gelo picadoGelo picado2 kg
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
17

Troubleshooting

Ice-chamber churn troubleshooting.

Flow

Loading...
18

History and honest limits

**James H. Bump** of Morris, Otsego County, New York, US 21,871, 26 October 1858, "Churn". He held that the cream, "by the absorption of oxygen is fully acetified" and kept cool by the iced air, gives butter "of a superior quality". He disclaimed a hollow dasher rod for air and forcing air into cream as done before, and claimed only the chamber C through which the air is made to circulate. He gave no sizes and named only "metal boxes": every size, material and the 8 litres at 15 °C are ours. Our notches in box a' stand in for his grooves cut in lid D.

Materiais

14

Ferramentas necessárias

15

Ficheiros de design

8

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...