Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Rocking Bucket-Dasher Churn: A Crank and Rod Rock a Dasher of Bucketed Arms, a Fixed Bucket Breaks the Current
Gillett Bunting of Liberty, Indiana, received US 26,226, dated 22 November 1859, for a churn-dasher. A dasher of crossed arms with buckets on their ends rocks on a level shaft whose bearings slide up or down to suit the amount of cream. A crank above, turned through a pair of cog wheels with a balance wheel, rocks it by a long rod, throwing the cream into opposing currents, and a fixed bucket on the bottom breaks the current along the floor.
The patent gives no sizes; every size here is ours.
Intermediário
About 2 days, plus printing
Instruções
1
1
How far the dasher rocks
How far the dasher rocks
A carregar o notebook Jupyter…
2
2
Agitators swung on pivots, two weeks before
Agitators swung on pivots, two weeks before
Cooper swings his agitators from a dash rod worked by hand. Bunting rocks a whole dasher from a crank.
3
3
Read US 26,226
Read US 26,226
"the rapid oscillating motion thus imparted to the dasher, through the medium of buckets (e' g', K) forces the cream into violent opposing currents, at the same time, the concussive action of the buckets (e', g') and arms (e, g) and bar (E) upon the cream is fully developed, thereby producing, a rapid and violent agitation of the cream"
4
4
Print the driving wheel G
Print the driving wheel G
Spur wheel, 48 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the wheel h
Print the wheel h
Spur pinion, 16 teeth, module 3, 15 mm face, with a hub bored 12.6 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Shell A, bed A', guides L and bucket K
Shell A, bed A', guides L and bucket K
Use a wooden tub 360 mm across inside at the floor, 320 mm at the top and 420 mm deep. Stand it on a bed board 520 x 560 mm between two guide strips. Glue and screw a hardwood block K, 60 x 300 x 60 mm, across the middle of the floor, with a 24 x 24 mm socket 50 mm deep near each end for the slides. Fill the tub with water overnight so it swells tight, then empty it.
Materiais para este passo:
Tina de madeira1 peça
Tábua de madeira de lei2 peças
Cola de madeira1 peça
Parafusos para madeira12 peçasFerramentas necessárias:
Serra de mesa
Serrote
Formão de samblagem
Maço de madeira
Berbequim sem fios
Jogo de brocas
Sargento de barra
Fita métrica
Água7
7
Slides f and the dasher
Slides f and the dasher
Cut two slides 20 x 24 mm, 255 mm long, bore each 21 mm 225 mm from its foot for the shaft's journal, and a row of 6 mm holes near the foot for a set screw through the block K. Make the shaft F a 20 mm hardwood dowel 280 mm long. Mortise through it two arms e 20 x 30 mm, 210 mm long, 150 mm apart, two arms g 20 x 30 mm, 260 mm long, at right angles to them, 80 mm apart, and the bar E 20 x 30 mm, 235 mm long, between the arms e, its long end reaching 100 mm past the shaft and bored 12.6 mm. Screw three U-channel buckets 170 x 40 x 20 mm of hardwood across the ends: one on the arms e and E's short end, one on each end of the arms g. Stand the slides in K with the shaft's ends in them, 240 mm up.
Materiais para este passo:
Tábua de madeira de lei2 peças
Cavilhas de madeira dura1 peça
Cola de madeira1 peça
Parafusos para madeira24 peças
Sortido de parafusos sextavados2 peçasFerramentas necessárias:
Serra de mesa
Tupia
Formão de samblagem
Maço de madeira
Berbequim sem fios
Jogo de brocas
Lixa
Fita métrica8
8
Frame B, crank shaft C, wheels and rod D
Frame B, crank shaft C, wheels and rod D
Bolt two posts of 40 x 30 mm hardwood to the bed beside the tub, 400 mm apart, 850 mm tall, and bore them 12.6 mm 690 mm above the tub's floor. Bend a 12 mm stainless shaft C into a crank of 50 mm throw in its middle, heating the bends red with the torch, and run it through the posts over the bar E's end. Pin the wheel h on one end and a hardwood balance wheel k, 260 mm across and 30 mm thick, on the other. Fix a 20 mm stud above h for the wheel G, meshing, with a crank handle H. Join the crank to E's end with a hardwood rod D, 450 mm between its pins.
Materiais para este passo:
Madeira macia de 70x70 mm1 peça
Tábua de madeira de lei2 peças
Varão de aço inoxidável2 peças
Shaft Collar2 peças
Contrapino4 peças
Anilha plana6 peças
Sortido de parafusos sextavados4 peças
Porca de segurança com anel de nylon4 peças
Filamento PETG1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Maçarico a propano
Torno de bancada
Martelo
Luvas resistentes ao calor
Serra tico-tico
Bússola
Serra de arco para metais
Limas (lima de mão)
Berbequim sem fios
Jogo de brocas
Chave inglesa ajustável9
9
The build in 3D
The build in 3D
FreeCAD model of this build, the tub cut through the middle: the bed and guides, the fixed bucket K with the two slides, the dasher with its arms, bar E and three buckets, the rod D up to the cranked shaft C, the wheels G and h, the crank H and the balance wheel. The crank was turned through 24 positions.
10
10
Churn
Churn
Pour in heavy cream at about 15 °C, checked with the thermometer; for less cream, lower the slides in K so the dasher still works in it. Turn the crank H steadily, timing it. When the butter comes, lift the rod off the crank and the dasher out on its slides, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater15 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável11
11
Troubleshooting
Troubleshooting
Rocking dasher troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Gillett Bunting** of Liberty, Union County, Indiana, assignor to himself and W. M. Jarrell, US 26,226, 22 November 1859, "Churn-Dasher". He disclaimed hinged churn-dashers and oscillating movement as such, and claimed the vibrating movement of the dasher by the arms with the crank, driving wheel and connecting rod, with the current breaker K. The patent gives no sizes; every size here is ours. His frame B stands on the shell's top; ours is two posts on the bed beside it.
Materiais
16- 1 peçaReferência
- 2 peçasReferência
- 2 peçasReferência
- 36 peçasReferência
- 1 peçaReferência
- Referência
- Referência
- 2 peçasReferência
- 2 peçasReferência
- 4 peçasReferência
- 6 peçasReferência
- Referência
- 1 peçaReferência
- 15 lReferência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
25- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
3Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Folding-Lever Dasher Churn: The Dash Rod Folds Two Levers and Swings the Agitators Side to Side
por Buttercup
Marcenaria
7
0
0
0
0
0

Segmental-Stave Churn: Thick Curved Staves Split the Cream's Current, a Long Blade Sweeps Beneath Them
por Buttercup
Marcenaria
5
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

