Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Folding-Lever Dasher Churn: The Dash Rod Folds Two Levers and Swings the Agitators Side to Side
N. B. Cooper of Gratis, Ohio, received US 26,020, dated 8 November 1859, for a churn-dasher. A frame slides into ways on the churn's ends and lifts out whole. Two bars run along its foot on pivots, one each side of the middle, each with blades and the lower half of a folding lever; the levers' upper halves meet at the dash rod. Working the rod up and down folds the levers and swings the bars and their agitators, driving the cream from side to side.
The patent gives no sizes; every size here is ours.
Intermediário
About 2 days
Instruções
1
1
The folding levers
The folding levers
A carregar o notebook Jupyter…
2
2
Dashers that swing sideways, six weeks before
Dashers that swing sideways, six weeks before
Austin swung his side dashers from cranks. Cooper swings his agitators from the dash rod itself, by folding levers.
3
3
Read US 26,020
Read US 26,020
"It will be readily seen by reference to Fig. 2 that the operation of the levers and agitators is of such a character as to force the cream rapidly from one side of the churn to the other, and that such currents must be forcibly interrupted by the agitators upon either side"
4
4
Shell A and ways x
Shell A and ways x
From 20 mm hardwood make a box 400 x 320 mm and 420 mm deep inside. Glue two strips 15 x 15 mm up the inside of each end, 90 mm apart, as the ways x. Fill the box with water overnight so it swells tight, then empty it.
Materiais para este passo:
Tábua de madeira de lei3 peças
Cola de madeira1 peça
Parafusos para madeira24 peçasFerramentas necessárias:
Serra de mesa
Serrote
Berbequim sem fios
Jogo de brocas
Sargento de barra
Esquadro fixo
Fita métrica
Água5
5
Frame B
Frame B
Cut two end posts 89 x 14 mm, 460 mm long, to slide between the ways, and a top bar 400 x 40 x 30 mm with a 31 mm square hole in its middle for the dash rod; screw the bar across the posts' tops. Screw a block 16 x 24 x 24 mm to each post's inside 25 mm each side of the middle and 110 mm up, and bore them 10.4 mm for the pivot rods b'.
Materiais para este passo:
Tábua de madeira de lei1 peça
Cola de madeira1 peça
Parafusos para madeira12 peçasFerramentas necessárias:
Serra de mesa
Formão de samblagem
Maço de madeira
Berbequim sem fios
Jogo de brocas
Esquadro fixo6
6
Bars b, blades c and folding levers d
Bars b, blades c and folding levers d
Bore two hardwood bars 20 mm square and 336 mm long through their length, 10.4 mm, and pin each on a 10 mm stainless rod 396 mm long that turns in the blocks. In the middle of each bar fix a lower arm, 110 mm between its pin holes, pointing up and out, and fix two blades 54 x 50 x 8 mm at right angles to it, pointing down and out, staggered so the two bars' blades pass each other. Join each arm's end to an upper lever, 180 mm between pins, and both upper levers to the foot of a dash rod 30 mm square and 550 mm long, with 10 mm stainless pins, washers and split pins. Glue two agitator bars f, 16 mm square and 340 mm long, across each upper lever.
Materiais para este passo:
Tábua de madeira de lei2 peças
Varão de aço inoxidável2 peças
Cavilhas de madeira dura1 peça
Cola de madeira1 peça
Anilha plana8 peças
Contrapino8 peçasFerramentas necessárias:
Serra de mesa
Serra de arco para metais
Limas (lima de mão)
Berbequim sem fios
Jogo de brocas
Lixa
Fita métrica7
7
The build in 3D
The build in 3D
FreeCAD model of this build, one side and one end left off: the shell with its ways, the frame with the pivot rods and the dash rod, the two bars with their arms and blades, the upper levers with the agitator bars. The bars were turned from 40 degrees up to 40 degrees down.
8
8
Churn
Churn
Pour about 25 litres of heavy cream at about 15 °C into the shell, checked with the thermometer. Slide the frame down the ways and work the dash rod up and down steadily, timing it. When the butter comes, lift the frame out whole, gather the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater25 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável9
9
Troubleshooting
Troubleshooting
Folding-lever churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**N. B. Cooper** of Gratis, Preble County, Ohio, US 26,020, 8 November 1859, "Churn-Dasher". He did not claim jointed levers or agitators on them, "as these devices are well known", but "the arrangement of the arms d, d, on the two pivots b', b', one on each side of the upright B, when the upright B is made removable, by means of the ways x, x". The patent gives no sizes; every size here is ours. His central upright is here the top bar's guide, and the rod is worked by hand rather than by gearing and a crank.
Materiais
10- 3 peçasReferência
- 3 peçasReferência
- 36 peçasReferência
- 2 peçasReferência
- 1 peçaReferência
- 8 peçasReferência
- 8 peçasReferência
- 25 lReferência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
17- 1 vendor sell this, none ship to you yetReferência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
1Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Three-Crank Churn: One Dasher Strokes Up and Down While Two Side Dashers Swing In and Out
por Buttercup
Marcenaria
9
0
0
0
0
0

Oval-Breaker Rod Dasher: Breakers Strung on Two Rods, Add More for More Agitation
por Buttercup
Marcenaria
5
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

