Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Screw-Piston Box Churn: The Case Turns and a Piston Runs End to End Along a Five-Start Screw
Buttercup

Criado por

Buttercup

10. novembro 2026IE
7
0
0
0
0

Screw-Piston Box Churn: The Case Turns and a Piston Runs End to End Along a Five-Start Screw

E. L. Pratt of Philadelphia received US 25,306, dated 30 August 1859, for a square box churn with a piston inside. A screw of four or five threads runs the length of the case; the piston rides on it. With the screw held still, turning the case drives the piston from one end to the other, forcing the cream through small grooves across its edges and through holes that a turning disk opens or closes. To finish, the case is held and the screw turned, so the piston presses the butter into each end. Pratt gives no sizes; every size here is ours.
Avançado
About 3 days, plus printing

Instruções

1

Cream through the grooves

A carregar o notebook Jupyter…
2

Cream forced through small openings, two weeks before

Lehaye pumped the cream through slots he could narrow. Pratt drives a piston along a screw and narrows its holes with a disk.
3

Read US 25,306

"The operator now takes hold of the crank handle (h) and gives rotary motion to the case (A), thus causing the diaphragm or piston (C) to be forced, by the screw shaft (D), toward, and eventually against, one of the ends (e or e') of the said case (A), when he then gives an opposite rotary motion to the said case (A), and thus forces the said diaphragm (C) to the other end of the same".
4

Print the screw sections

One 100 mm section of the five-start screw, 50 mm across with a 50 mm lead, bored 12.4 mm for the rod. Print four, standing up. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
5

Print the piston's outer plate m

A 196 mm square plate 10 mm thick with the five-start nut, eight 16 mm holes o and grooves p across its edges. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Print the piston's other outer plate m

The same plate with an arc slot for the disk's peg. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
7

Print the piston's middle plate m'

The middle plate with a 140.6 mm hole for the turning disk. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
8

Print the disk n

The 140 mm disk with eight holes set between the plates' holes and a peg that comes out through the slot. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
9

Case A: sides d, ends e and e', bolts f

From 20 mm hardwood cut four sides 412 mm long, two 200 mm and two 240 mm wide, and two end pieces 280 x 280 x 40 mm. Rout a groove 6 mm deep and 20.5 mm wide in each end's inner face to take the sides' edges as a square 200 mm inside. Cut a 180 x 120 mm opening in one 200 mm side for the lid. Bore the ends 11 mm at the four corners, 128 mm from the middle each way, and draw the case together with four M10 rods, washers and nuts. Bore a blind 20.6 mm hole 30 mm deep in the middle of one end for journal i, and a 20.6 mm hole through the other for journal k. Soak the case in water overnight so it swells tight.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei3 peças
Varão roscadoVarão roscado4 peças
Porca sextavadaPorca sextavada8 peças
Anilha planaAnilha plana8 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
SerroteSerrote
FormõesFormões
Berbequim sem fiosBerbequim sem fios
Conjunto de brocas de páConjunto de brocas de pá
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Esquadro fixoEsquadro fixo
Chave inglesa ajustávelChave inglesa ajustável
ÁguaÁgua
10

Screw shaft D and its journals

Thread the four screw sections on a 580 mm M12 stainless rod so their threads run on from one to the next, with a 20 mm stainless tube on each side as journals i and k. Clamp the stack with nuts and washers so the screw turns with the rod. Thread the piston on before the last section goes on. Put journal i in the blind hole, pass journal k through the other end, and draw the case up round them.

Materiais para este passo:

Varão roscadoVarão roscado1 peça
Tubo de aço inoxidávelTubo de aço inoxidável1 peça
Porca sextavadaPorca sextavada4 peças
Anilha planaAnilha plana4 peças
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Chave inglesa ajustávelChave inglesa ajustável
11

Piston C

Glue the middle plate to the plain outer plate, drop the disk into its hole, peg up, and glue the slotted plate on top so the peg comes out through the slot and the disk turns freely. Line up the nuts' threads before the glue sets by running the piston onto a screw section.

Materiais para este passo:

Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Sargento de barraSargento de barra
12

Lid q, frame B, cranks and pin v

Make the lid from hardwood to fit the opening, with a 6 mm lip all round, and two hardwood buttons r screwed to the case to turn over it. Fix a hardwood block on the outside of end e and pin a 20 mm steel stub in it as journal g, with a crank h. Fix a crank l on the rod's end outside journal k. Build a frame of two uprights on a base, 580 mm apart, with open slots for the journals. Bore 10 mm holes through each upright and its end piece, and through the crank l, for the pin v.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Madeira macia de 70x70 mmMadeira macia de 70x70 mm2 peças
Barra de aço em brutoBarra de aço em bruto2 peças
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Parafusos para madeiraParafusos para madeira16 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Conjunto de brocas de páConjunto de brocas de pá
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Fita métricaFita métrica
13

The build in 3D

FreeCAD model of this build, the case cut open: the sides let into the ends and held by the four corner bolts, the lid and its buttons, the five-start screw on its journals, the piston in the middle with its grooves and holes, the two cranks and the frame. The case was turned through 16 angles.
Arquivo de designBLENDCC0 - Free
14

Churn, then press

Turn the disk's peg to open or close the holes for the cream's thickness. Pour about 6 litres of heavy cream at about 15 °C, checked with the thermometer, through the lid opening, button the lid down and pin crank l to its upright. Turn crank h one way about seven and a half turns until the piston stops at one end, then back the other way, timing it. When the butter comes, pin the case instead and turn crank l to drive the piston against each end and press the butter there. Open the lid, lift the butter out, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater6 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
15

Troubleshooting

Screw-piston churn troubleshooting.

Flow

Loading...
16

History and honest limits

**E. L. Pratt** of Philadelphia, assignor to himself and R. B. Fitts, US 25,306, 30 August 1859, "Churn". He claimed the rotary case with a piston that both moves along and turns on a screw, with grooves across its edges, and the piston of three pieces with a disk to open, adjust or close its holes. He gives no sizes, so every size here is ours; he made the piston of wood, and ours is printed, with a peg through a slot to turn the disk.

Materiais

14

Ferramentas necessárias

19

Ficheiros de design

6

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...