Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Rack-and-Pawl Plunge Router: The Motor Rides One Post on a Spring and Steps Down a Tooth at a Time (Carter, 1925)
Forge

Criado por

Forge

13. novembro 2026NO
12
0
0
0
0

Rack-and-Pawl Plunge Router: The Motor Rides One Post on a Spring and Steps Down a Tooth at a Time (Carter, 1925)

Ray L. Carter of Syracuse, New York, improved his 1924 router with US 1,565,790, dated 15 December 1925. The motor's holder now slides up and down a single strong post on a large round base, and a spring inside the post holds it up off the work. Each press of a lever moves the holder down one tooth of a rack, so a deep cavity is cut in stages. A locking pawl holds each step. Gauge nuts on a plunger stem set the final depth, and pressing the pawl's foot lets the spring lift the cutter clear. We reuse our 1924 router's printed motor casing in a printed holder on a square steel post. The sizes are ours.
Avançado
About 3 days

Instruções

1

Cutting deep in stages

A carregar o notebook Jupyter…
2

Read US 1,565,790

"By this arrangement cavities of considerable depth may be routed by successive stages wherein each stage represents the normal depth the tool is designed to cut."
3

The motor and its casing come from the 1924 router

Print the casing and fit the motor, collet and switch exactly as in Carter's 1924 router; here the casing screws into a holder on a post instead of into a base.
4

Print the holder

The holder 7: a split ring threaded for the 1924 casing, clamp lugs for a thumb screw, and beside it the guide 7c with a square opening for a 1 in tube, a recess for the gib plate, two set-screw holes and the rack 17 of 3 mm teeth on its outer face. Print it rack upright. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
Arquivo de designSTLCC0 - Free
5

Print the base

The base 9: a round plate 170 mm across with a 50 mm opening, and the boss 9' with a square socket for the post and a hole for its cross bolt. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
Arquivo de designSTLCC0 - Free
6

The hollow post 8

Cut 1 inch square steel tube 200 mm long. Saw and file a slot 8b 6 mm wide and 100 mm long down the middle of one wall, starting 40 mm from the top. Push the post into the base's socket and bolt it through with an M6 bolt and lock nut. Drop a compression spring 10 into the post, then a plunger 13: a block of flat bar that slides in the tube, tapped M6 on its back for the screw that runs in the slot, with an M6 rod 13' standing up from it. Screw a flat-bar cap 12 across the post's top with a hole for the rod, and run two gauge nuts 14, 14' onto the rod above it.

Materiais para este passo:

Mild Steel Square Tube 1" x 1"Mild Steel Square Tube 1" x 1"1 peça
Barra chata de aço macioBarra chata de aço macio1 peça
Conjunto de molas de compressãoConjunto de molas de compressão1 peça
Varão roscadoVarão roscado1 peça
Porca sextavadaPorca sextavada2 peças
Sortido de parafusos sextavadosSortido de parafusos sextavados3 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de limasJogo de limas
Torno de bancadaTorno de bancada
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Jogo de machos e cossinetesJogo de machos e cossinetes
Desandador de machosDesandador de machos
Chave inglesa ajustávelChave inglesa ajustável
Óculos de segurançaÓculos de segurança
7

Holder on the post

Print the holder and base. Lay a strip of flat bar in the guide's recess 15 as the gib plate 15' and run two M5 set screws 16 against it, one with a wing nut on its head to lock the holder by hand. Slide the guide down over the post and fix it to the plunger with an M6 screw through the slot. Set the screws so the holder slides freely without rattling. Screw the 1924 motor casing into the holder and lock it with an M5 screw and wing nut through the lugs.

Materiais para este passo:

Filamento PETGFilamento PETG1 peça
Barra chata de aço macioBarra chata de aço macio1 peça
Parafuso sem cabeça de ponta côncavaParafuso sem cabeça de ponta côncava2 peças
Porca borboletaPorca borboleta2 peças
Parafuso de cabeça cilíndrica com sextavado interiorParafuso de cabeça cilíndrica com sextavado interior2 peças

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Rebarbador manualRebarbador manual
Jogo de chaves AllenJogo de chaves Allen
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
8

Pawls and lever

File a pawl 18 from flat bar with a hook 18' at its top to catch the rack's teeth, and a locking pawl 20 with a tooth 20' at its top and its lower end bent out as a foot 20d. Pivot the locking pawl on the base's boss with an M5 screw, held against the rack by a spring-steel leaf 20b. Pivot one end of a lever 19 on the boss and the pawl's lower end to the lever partway along, with a second leaf 20c holding the pawl to the rack. Each press of the lever's handle pulls the holder down one tooth, and the locking pawl drops in under it.

Materiais para este passo:

Barra chata de aço macioBarra chata de aço macio2 peças
Fita de aço-molaFita de aço-mola1 peça
Parafuso de cabeça cilíndrica com sextavado interiorParafuso de cabeça cilíndrica com sextavado interior3 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon3 peças

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de limasJogo de limas
Torno de bancadaTorno de bancada
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Chave inglesa ajustávelChave inglesa ajustável
9

Rout a deep recess

Fit a straight bit. Set the gauge nuts so the plunger's rod stops on the cap at the depth wanted. Clamp a board, rest the base on it with the cutter clear, switch on, press the lever once and move the router across the area; press again and repeat, until the nuts stop it. Press the locking pawl's foot and the spring lifts the cutter out.

Ferramentas necessárias:

Conjunto de fresas de tupiaConjunto de fresas de tupia
Tábua de madeira de leiTábua de madeira de lei
Sargento de barraSargento de barra
Óculos de segurançaÓculos de segurança
10

Troubleshooting

Plunge router troubleshooting.

Flow

Loading...
11

History and honest limits

**Ray L. Carter** of Syracuse, New York, US 1,565,790, dated 15 December 1925, filed 21 March 1925, improving his US 1,514,894. He describes a holder "formed at one side with a guide portion having an angular vertical opening, for slidably mounting the holder upon a pedestal or post of substantially the same angularity", a coil spring housed in the pedestal, a ratchet rack and pawl to move the motor step by step, a locking pawl, gauge nuts, and a plate with set screws to take up wear. His post is triangular and cast; ours is 1 inch square steel tube. His holder and base are metal; ours are printed PETG. His motor ran on mains; ours is the small DC motor of our 1924 router. The sizes are ours.

Materiais

12

Ferramentas necessárias

16

Ficheiros de design

2

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...