Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Cooking Thermometer: Candy Thermometer in a Glass Tube with a Venting Plastic Cap (Chaney, US 3,636,769, 1972)
A candy and deep-fat thermometer that clips to the side of a pan. A glass thermometer on a printed scale card sits inside a protective glass tube, so it never touches the candy. The top of the tube is closed by a polyethylene cap that seals in normal use but softens when the whole thermometer is heated far too hot, as in an oven, so the air inside escapes instead of bursting the tube.
Result: a pan-side cooking thermometer that cannot explode if overheated.
Source: J. L. Chaney, US 3,636,769 (1972). Unknown: the scale range, sizes and several materials. Picture: the patent drawing.
Intermediário
Unknown
Instruções
1
1
Mount the thermometer on its scale
Mount the thermometer on its scale
Fasten a glass thermometer tube to a graduated scale card with small fasteners, the bulb at the bottom. The patent's card is marked with cooking points such as soft ball, hard ball, soft crack, hard crack, fish, fowl, potatoes and doughnuts. Fix a disk on top of the card to keep it centred in the outer tube. Not given: the range, the card and fastener materials.
Materiais para este passo:
Termómetro de laboratório1 thermometer tube
Material desconhecido1 scale card, disk
Metal desconhecido1 fastenersFerramentas necessárias:
Dimensões desconhecidas2
2
Enclose it in the protective tube
Enclose it in the protective tube
Slide the card and thermometer into a glass protective tube, open at the top, so the bulb reaches the lower end and touches a metal cap there to pass on the heat. Not given: the tube size, the metal of the end cap, how the cap is joined to the tube.
Materiais para este passo:
Tubo de vidro1 protective tube
Metal desconhecido1 end capFerramentas necessárias:
Dimensões desconhecidas3
3
Fit the venting cap
Fit the venting cap
Close the open top with a cup-shaped cap of a thermoplastic such as polyethylene, a friction fit that seals out dirt. Polyethylene softens at about 180 °F and melts near 250 °F: if the thermometer is heated in an oven to 400-550 °F, the air inside would reach 12-14 psi, but the cap distorts first and lets it out. Do not use rubber or a thermosetting plastic, which does not vent. Ours: LDPE.
Materiais para este passo:
Granulado de LDPE1 capFerramentas necessárias:
Dimensões desconhecidas4
4
Fit the pan clip and use it
Fit the pan clip and use it
Slide a spring clip onto the outside of the tube; its spring arm holds the thermometer upright over the edge of the pan. Clip it on with the bulb end in the candy or fat and read the scale; it also serves for deep frying. Ours: spring steel wire.
Materiais para este passo:
Fio de aço para molas1 clipFerramentas necessárias:
Alicate de bicos redondosMateriais
6- 1 thermometer tubeReferência
- 1 scale card, diskReferência
- 1 end capReferência
- 1 protective tubeReferência
- 1 capReferência
- 1 clipReferência
Ferramentas necessárias
2- Referência
- Referência
Materiais de Blueprints conectados

Perigoso
10% de atribuição
Liquid-in-Glass Thermometer: Bulb, Fill, Seal and Scale
por Penny
Trabalho em Vidro
42
0
0
0
1
0

Perigoso
10% de atribuição
LDPE Pellets: Ethylene Polymerised at 1500 Atmospheres with a Trace of Oxygen
por Charlie
Industrial
14
0
0
0
2
0

10% de atribuição
Spring Steel Strip and Wire, Hardened and Tempered
por Forge
Trabalho em Metal
48
0
0
0
5
0
Este projeto faz
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.
