Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Spring-Pole Cam Churn: A Two-Arc Cam Lifts a Hinged Strip Dasher and a Wooden Spring Pole Drives It Down
Buttercup

Criado por

Buttercup

11. novembro 2026IE
4
0
0
0
0

Spring-Pole Cam Churn: A Two-Arc Cam Lifts a Hinged Strip Dasher and a Wooden Spring Pole Drives It Down

Alexander W. Cunningham of West Middleton, Pennsylvania, received US 27,276, dated 28 February 1860, for a churn. A box deeper at the rear holds a dasher of strips set edge-on, hinged on a lever at the front. A cam of two semicircular arcs lifts the dasher slowly; when each arc's end passes the roller, a spring pole of hickory under the box drives it down with force. Two strokes to each turn of the crank. The patent gives no sizes; every size here is ours.
Avançado
About 3 days, plus printing

Instruções

1

Two half-circles on one shaft

A carregar o notebook Jupyter…
2

Two dasher strokes to a turn, one week before

Clement gets two strokes a turn from a toggle. Cunningham gets them from a cam of two arcs.
3

A dasher worked by a lever

Cooper's dasher hangs on levers. Cunningham hinges his whole dasher on one lever at the box's front.
4

Read US 27,276

"The cam p consists of two semicircular arcs, one extremity of each arc being placed at the center of the other semicircular arc, the arcs being united by their chords and the shaft passing through the chords at a point midway between the inner extremities of the two arcs." ... "On turning the shaft, the dasher is raised up gradually, and falls suddenly with the full force of the spring pole."
5

Print the cam p

Two semicircular arcs of 80 mm radius, a band 10 mm thick and 20 wide, joined along their chords by a bar 250 mm long, with a hub bored 20.6 mm midway between the arcs' inner ends. PETG, 0.2 mm layers, 100 % infill.
Arquivo de designSTLCC0 - Free
6

Box a, cover and feet

From 20 mm hardwood board make a box 700 mm long and 260 wide inside, 200 mm deep at the front end and 375 at the rear: cut the sides with their lower edges sloping 175 mm over the length, glue and screw the ends and bottom between them, and seal the inside joints with silicone sealant. Cut a slot 44 x 95 mm in the front end's middle, 20 to 115 mm above the inside floor, for the lever. Hinge a cover on the top and drill a 10 mm air hole t in it. Screw two front feet b, 40 x 40 mm, 460 mm long, to the sides' outer faces 160 mm behind the front, and two rear feet c, 340 mm long, 640 mm behind it, so the sides stand upright and the bottom falls to the rear. Hinge a small frame d (two legs 305 mm and a bar) to the front feet, folded up; let it down to raise the front end.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei4 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira60 peças
Vedante de siliconeVedante de silicone1 peça
Dobradiça de livro para móvelDobradiça de livro para móvel4 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
LixaLixa
7

Dasher strips e, cross pieces f and lever g

Cut five hardwood strips 20 x 20 mm, 600 mm long, and set them in two cross pieces f, 30 x 25 mm, 240 long, 54 mm apart and turned 45 degrees, so each presents an edge to the cream. Cut a hardwood lever 40 x 30 mm, 977 mm long; bore it 12.8 mm across 265 mm from one end for the pivot h, and 15 mm from that end for the pin i; saw a slot 22 mm wide from that end for 165 mm, for the roller. Screw the cross pieces under the long arm so the strips lie 2 mm above the floor when it rests along it. Pivot the lever on a 12 mm stainless pin in two hardwood brackets on the front end's outer face, 35 mm out and 70 mm above the inside floor, the long arm through the slot.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira12 peças
Varão de aço inoxidávelVarão de aço inoxidável1 peça
ContrapinoContrapino2 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
8

Roller n, pitman k, spring pole l and cross piece m

Cut a roller 40 mm across and 20 long from hardwood dowel, bore it 12.6 mm and set it in the lever's slot on a 12 mm stainless pin i. On the pin's ends outside the lever hang two hardwood pitman links 8 x 30 mm with holes 200 mm apart. Cut a spring pole 40 x 25 mm, about 1010 mm long, from straight-grained ash (the patent: "hickory or other suitable wood"); screw its rear end to a block under the bottom's rear, run it forward under the box, and hold it up on a hardwood cross piece m hung from the sides 590 mm from the front. Pin its front end between the pitman links; it should lift the lever's short arm so the dasher rests on the floor.

Materiais para este passo:

Cavilhas de madeira duraCavilhas de madeira dura1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Tábua de freixoTábua de freixo1 peça
Parafusos para madeiraParafusos para madeira8 peças
ContrapinoContrapino4 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Conjunto de chaves de fendasConjunto de chaves de fendas
9

Arms, shaft q, cam p and crank s

Bolt two hardwood arms 15 x 30 mm, 450 mm long, along the box's sides, reaching 300 mm out in front, and bore their ends 20.8 mm across directly above the roller, 70 mm above its centre at rest. Pass a 20 mm stainless shaft through them with the cam on it over the roller, held by collars; fit a hardwood crank 150 mm long with a dowel handle on one end. Set the cam so each arc meets the roller by its inner end as the crank turns.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Parafuso de carroçariaParafuso de carroçaria4 peças
Porca borboletaPorca borboleta4 peças
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Shaft CollarShaft Collar2 peças
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Chave inglesa ajustávelChave inglesa ajustável
10

The build in 3D

FreeCAD model of this build, the box cut through the middle: the strip dasher on the lever g, the pivot h, the roller and pitman, the spring pole under the bottom on the cross piece m, and the two-arc cam on its shaft and crank in front.
Arquivo de designBLENDCC0 - Free
11

Churn

Pour in about 15 litres of heavy cream at about 15 °C, checked with the thermometer: no more, as the patent says the box "must not be filled so full as to cover the dasher with cream when it is raised". Close the cover and turn the crank steadily, timing it: the dasher rises slowly and falls hard, twice a turn. When the butter comes, let down the frame d to raise the front end, as the patent advises, so everything runs to the rear; lift the cover and dasher, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater15 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
12

Troubleshooting

Spring-pole cam churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Alexander W. Cunningham** of West Middleton, Washington County, Pennsylvania, US 27,276, 28 February 1860, "Churn". He claimed the spring dasher worked by a cam, made of longitudinal strips presenting their angular edge to the cream, with a box deeper at one end than the other. The text calls the frame on the front feet both d and u. The patent gives no sizes or materials beyond the hickory pole; every size here is ours, our pole is ash, and our cam is printed.

Materiais

16

Ferramentas necessárias

18

Ficheiros de design

2

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...