Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
DC Power Supply: SCR-Regulated, Voltage and Current Bridges with Automatic Cross-Over (Kupferberg & Ash, Forbro, US 3,305,763, 1967)
Ed

Criado por

Ed

3. novembro 2026FI
8
0
0
0
0

DC Power Supply: SCR-Regulated, Voltage and Current Bridges with Automatic Cross-Over (Kupferberg & Ash, Forbro, US 3,305,763, 1967)

A variable DC supply regulated by controlled rectifiers instead of a series transistor. Two of the four rectifiers in the bridge are silicon controlled rectifiers; how late in each half-cycle they are fired sets the output. A voltage bridge and a current bridge each make an error signal, an analog OR gate passes whichever is larger, and the supply crosses over automatically between holding the voltage and holding the current. Result: a variable voltage / current regulated DC supply with automatic cross-over. Source: K. Kupferberg and J. Ash (Forbro Design), US 3,305,763 (1967), Fig. 1. Unknown: component values and the firing-angle circuit. Picture: the patent drawing.
Avançado
Unknown

Instruções

1

Build the controlled rectifier bridge

In a case, wire the cord through a switch and fuse to a transformer. Feed its secondary into a bridge of two ordinary rectifiers and two silicon controlled rectifiers. Smooth the negative output through a choke and a capacitor, then through a current-sensing resistor (with a second capacitor forming a further filter) to the negative output terminal; the positive goes straight to the positive terminal. Ours: the case, switch and fuse. Not given: the ratings.

Materiais para este passo:

Caixa de alumínioCaixa de alumínio1 peça
Cabo flexível com fichaCabo flexível com ficha1 peça
Interruptor de alavancaInterruptor de alavanca1 peça
FusívelFusível1 peça
Transformador AbaixadorTransformador Abaixador1 peça
DíodoDíodo2 peças
Tiristor (SCR)Tiristor (SCR)2 peças
Bobina de filtroBobina de filtro1 peça
Condensador eletrolíticoCondensador eletrolítico2 peças
Borne de painelBorne de painel2 output + and -

Ferramentas necessárias:

Berbequim de mãoBerbequim de mão
Conjunto de chaves de fendasConjunto de chaves de fendas
2

Build the two bridges

Current bridge: the sensing resistor, a reference Zener, a fixed resistor and the variable current-control resistor. Voltage bridge: the load across the output, the variable voltage-control resistor, a fixed resistor and a second reference Zener. Feed both Zeners from a small separate supply. Not given: the values, the Zener supply.

Materiais para este passo:

Díodo ZenerDíodo Zener2 peças
ReóstatoReóstato2 voltage and current controls
ResistênciaResistência1 sensing and bridge resistors

Ferramentas necessárias:

Ferro de soldarFerro de soldar
3

Build the control chain and use it

Invert the current bridge's error in a phase-reversing amplifier and feed it, with the voltage bridge's error, to an analog OR gate that passes the larger. Amplify the result and feed it to a firing-angle control circuit that fires the two controlled rectifiers' gates later or earlier in each half-cycle. In use, set the voltage and the current: for any load larger than the cross-over resistance (voltage setting divided by current setting) the supply holds the voltage, for a smaller one the current. Not given: the amplifier, OR-gate and firing circuits in this form.

Materiais para este passo:

Placa de circuito impressoPlaca de circuito impresso1 peça
Sortido de transístoresSortido de transístores1 amplifiers
Material desconhecidoMaterial desconhecido1 OR gate and firing-angle circuit
Fio de soldaFio de solda1 as needed

Ferramentas necessárias:

Ferro de soldarFerro de soldar

Materiais

17

Ferramentas necessárias

3

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...