Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Rolling-Rocker Churn: A Box on Pegged Rockers Rolls Along Notched Ways So Its Fulcrum Follows the Cream
Buttercup

Criado por

Buttercup

11. novembro 2026IE
5
0
0
0
0

Rolling-Rocker Churn: A Box on Pegged Rockers Rolls Along Notched Ways So Its Fulcrum Follows the Cream

Daniel Deshon 2d of Somerset, Pennsylvania, received US 27,701, dated 3 April 1860, for a churn. A box of cream stands on curved rockers whose pegs sit in notches along the ways of a stand. Rocked by a handle, the box tips end to end and the cream runs through racks of rods; as the rockers roll, the point they rest on moves along with the weight, so little force is needed. The patent gives no sizes; every size here is ours, and so is our reading of where the racks sit.
Intermediário
About 2 days

Instruções

1

A fulcrum that walks

A carregar o notebook Jupyter…
2

Cream rushing end to end through pins, one month before

Newbrough's barrel tips on a fixed pivot. Deshon's box rolls, so its pivot follows the cream.
3

Read US 27,701

"... this is done without contending but very little with the weight from the fact that the fulcrum at the bottom of the rockers (b) changes from one end to the other in accordance to the change of the weight inside of the vessel, always keeping in the center of the weight; consequently balancing the weight in its motion and saving most of the labor required to churn."
4

Vessel a and lid d

From 20 mm hardwood board make a box 600 x 250 mm inside and 290 deep; glue and screw it and seal the inside joints with silicone sealant. Cut a 150 mm opening across the middle of the top and a lid to fit it, with a hardwood block handle e.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei3 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira40 peças
Vedante de siliconeVedante de silicone1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
5

Racks i

Make two racks, each two hardwood side bars 24 x 20 mm, 355 long, with nine 10 mm stainless rods across between them. Stand them in the vessel leaning together, their feet on the floor 30 mm from the ends, meeting in the middle 240 mm above the floor.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável2 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
6

Rockers b with projections f, and handle c

Draw an arc of 400 mm radius with the compass on two 20 mm hardwood boards and cut each rocker with that arc as its bottom, 48 degrees of arc (325 mm), rising to the box's top; leave one 140 mm taller and cut a hand-hole in it as the handle c. Bore seven 12 mm holes along each arc, 6 degrees apart, and glue in dowel pegs standing 8 mm out as the projections f. Bolt a rocker on each long side of the vessel, centred, the arc's lowest point 40 mm below the vessel's bottom.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Parafuso de carroçariaParafuso de carroçaria4 peças
Porca borboletaPorca borboleta4 peças

Ferramentas necessárias:

BússolaBússola
Serra tico-ticoSerra tico-tico
TransferidorTransferidor
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
LixaLixa
Chave inglesa ajustávelChave inglesa ajustável
7

Pedestal h with ways and notches g

Cut two hardwood ways 520 x 120 x 30 mm and set them on edge under the rockers, 290 mm apart inside; join them with two cross boards near the floor. Cut seven notches 14 mm wide and 11 deep in each way's top edge, 41.9 mm apart from the middle, to match the pegs.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira16 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Conjunto de formões para madeiraConjunto de formões para madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
8

The build in 3D

FreeCAD model of this build, tipped 10 degrees and cut through the middle: the vessel with its lid and the two racks leaning together, the rockers with their pegs in the ways' notches, and the pedestal.
Arquivo de designBLENDCC0 - Free
9

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the vessel and close the lid. Push and pull the handle c steadily, tipping the vessel up to about 18 degrees each way, timing it. When the butter comes, lift the lid, take out the racks and the butter, tip the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater10 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
10

Troubleshooting

Rolling-rocker churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Daniel Deshon 2d** of Somerset, Pennsylvania, US 27,701, 3 April 1860, "Churn". He claimed the racks, vessel, pedestal and rockers with projections in notched ways, combined. He places the racks only by dotted lines in his figure; our two racks leaning together are our reading of them. Every size here is ours.

Materiais

11

Ferramentas necessárias

19

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...