Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Oblique-Slat Barrel Churn: Rows of Slats Inside a Turning Barrel Point Opposite Ways and Throw the Cream End to End
Pearson Embree of West Chester, Pennsylvania, received US 27,536, dated 20 March 1860, for a churn. Inside a common barrel churn turned by a crank, rows of wooden slats about a quarter of the diameter high point obliquely to the barrel's motion, each row the opposite way to the last. Some throw the cream toward one end, some toward the other; it strikes other slats or the projections on the heads and turns back.
The slats' height follows the patent's proportion; every other size here is ours.
Intermediário
About 2 days
Instruções
1
1
Slats a quarter of the diameter high
Slats a quarter of the diameter high
A carregar o notebook Jupyter…
2
2
Cream thrown end to end, two weeks before
Cream thrown end to end, two weeks before
Newbrough rocks his barrel so the cream runs end to end through pins. Embree turns his, and oblique slats throw it.
3
3
Read US 27,536
Read US 27,536
"The slats A A A, etc., throw the cream toward an end of the churn (one portion of the slats throwing to one end and the remaining portion to the other end); as the cream is thrown violently toward the end it either strikes other slats, or the projections B B by either of which means its course is reversed and great agitation of the cream produced."
4
4
Barrel, heads and door
Barrel, heads and door
Cut 430 mm of food-grade PE pipe 315 mm across with a 12 mm wall. Cut two heads from 15 mm HDPE sheet to fit inside it and bore both 20 mm on the centre. Cut a door 200 x 120 mm in the pipe's side, between two rows of slats; keep the piece, screw two HDPE strips along its long edges so it rests on the pipe, and hold it with two hooks and eyes.
Materiais para este passo:
Tubo de polietileno de alta densidade1 peça
Chapa de PEAD1 peça
Colchete (macho e fêmea)2 peças
Parafusos de máquina4 peças
Porca de segurança com anel de nylon4 peçasFerramentas necessárias:
Serra tico-tico
Berbequim sem fios
Jogo de brocas
Conjunto de brocas de pá
Limas (lima de mão)
Conjunto de chaves de fendas
Fita métrica5
5
Slats A, A', A'', A''' and projections B
Slats A, A', A'', A''' and projections B
Cut four hardwood strips 30 x 18 mm, 390 long, and sixteen hardwood slats 90 x 12 mm standing 73 mm from the barrel's wall, a quarter of its 291 mm inside diameter; round their ends if you like. Set four slats in each strip, 100 mm apart, each at 45 degrees to the strip: in the first and third strips one way, in the second and fourth the other. Screw the strips inside the barrel a quarter turn apart, through the wall with stainless screws and lock nuts, sealed with silicone, so each row points the opposite way from the row before. Screw two hardwood projections B, 20 x 90 mm and 30 deep, on each head's inner face, opposite each other, between the rows.
Materiais para este passo:
Tábua de madeira de lei1 peça
Cola de madeira1 peça
Parafusos de máquina16 peças
Porca de segurança com anel de nylon16 peças
Parafusos para madeira8 peçasFerramentas necessárias:
Serra de mesa
Transferidor
Berbequim sem fios
Jogo de brocas
Sargento de barra
Lixa
Conjunto de chaves de fendas
Chave inglesa ajustável6
6
Shaft, stand and crank
Shaft, stand and crank
Pass a 20 mm stainless shaft 680 mm long through both heads, press the heads into the pipe's ends, screw them through the wall and seal the heads and the shaft's passages with silicone sealant. Make a hardwood stand: a base 600 x 400 mm and two uprights 40 x 120 mm, 30 mm beyond each end of the barrel, bored 20.8 mm 260 mm above the floor. Rest the shaft in them with collars, and fit a hardwood crank 130 mm long with a dowel handle on its long end.
Materiais para este passo:
Varão de aço inoxidável1 peça
Parafusos de máquina8 peças
Tábua de madeira de lei2 peças
Cola de madeira1 peça
Parafusos para madeira8 peças
Shaft Collar2 peças
Cavilhas de madeira dura1 peçaFerramentas necessárias:
Serra de arco para metais
Limas (lima de mão)
Serra de mesa
Berbequim sem fios
Jogo de brocas
Conjunto de brocas de pá
Conjunto de chaves de fendas7
7
The build in 3D
The build in 3D
FreeCAD model of this build, the barrel cut through the middle: four rows of oblique slats, alternate rows pointing opposite ways, the projections B on the heads, the door, the shaft, stand and crank.
8
8
Churn
Churn
Turn the door uppermost, pour in about 8 litres of heavy cream at about 15 °C, checked with the thermometer, and close it. Turn the crank steadily, timing it. When the butter comes, stop with the door uppermost, open it, tip the buttermilk out into a bowl, take out the butter, wash it in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater8 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável9
9
Troubleshooting
Troubleshooting
Oblique-slat barrel churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Pearson Embree** of West Chester, Chester County, Pennsylvania, US 27,536, 20 March 1860, "Churn". He claimed the slats or projections on the inner surface, each row pointing obliquely in the line of motion and the next row the opposite way. He says they make butter "in much less time than by the ordinary revolving churns". The slat height follows his quarter-diameter; the PE barrel, the 45-degree angle, the counts and all other sizes are ours.
Materiais
15- Referência
- 1 peçaReferência
- 2 peçasReferência
- 28 peçasReferência
- Referência
- 2 peçasReferência
- 2 peçasReferência
- 2 peçasReferência
- 16 peçasReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
17- 1 vendor sell this, none ship to you yetReferência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
1Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Rocking Barrel Brake-Pin Churn: Cream Rushes End to End Through Rows of Pins, a Diagonal Board Gathers the Butter
por Buttercup
Marcenaria
7
0
0
0
0
0

Counter-Turning Cylinder Churn: The Ribbed Cylinder Turns One Way While the Dashers Inside Turn the Other
por Buttercup
Marcenaria
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

