Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Digital Tachometer: Hand-Held Contact Type That Holds Its Reading (Sugiyama, Shimpo, US 4,000,465, 1976)
Ed

Criado por

Ed

3. novembro 2026FI
11
0
0
0
0

Digital Tachometer: Hand-Held Contact Type That Holds Its Reading (Sugiyama, Shimpo, US 4,000,465, 1976)

A hand-held digital tachometer. You press the contact head on its shaft against the end of a turning shaft and push the thumb button; a slotted disk inside chops a light beam into pulses, and the pulses counted in a fixed time, set by a quartz clock, appear in the window as the speed. A latch holds the reading after you take the tachometer away, so you can read it even where you could not see the window while measuring. Result: a contact tachometer that shows revolutions per unit time and keeps the last reading. Source: Y. Sugiyama (Shimpo Kogyo), US 4,000,465 (1976). Unknown: the number of holes, the clock, the gate time and the circuit details. Picture: the patent drawing.
Avançado
Unknown

Instruções

1

Make the housing and measuring shaft

Make a cylindrical housing to hold in one hand, with a window in its side for the reading and a push button for the power switch where the thumb falls. Run a measuring shaft out of the front end in bearings and fit a contact head on its tip to press against the shaft being measured. Not given: materials, sizes. Ours: aluminium tube, a ball bearing.

Materiais para este passo:

Tubo de alumínioTubo de alumínio1 housing
Metal desconhecidoMetal desconhecido1 measuring shaft
Rolamento de esferasRolamento de esferas1 peça
Material desconhecidoMaterial desconhecido1 contact head

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Berbequim de mãoBerbequim de mão
Dimensões desconhecidasDimensões desconhecidas
2

Make the pulse generator

Fix a disk on the measuring shaft with a ring of small holes evenly spaced near its edge. Put a light source on one side of the disk and a photodetector on the other: each hole passing makes one pulse. Shape and amplify the pulses. Not given: the number of holes. Ours: an LED and a photodiode.

Materiais para este passo:

Material desconhecidoMaterial desconhecido1 slotted disk
Sortido de LEDSortido de LED1 light source
Fotodíodo (BPW34)Fotodíodo (BPW34)1 photodetector
ResistênciaResistência1 conjunto

Ferramentas necessárias:

Berbequim de mãoBerbequim de mão
3

Build the counting circuit

Divide a quartz oscillator's clock down to gate pulses one unit of time long. Pass the measurement pulses through an AND gate during each gate pulse into a counter. At the start of each gate pulse a reset pulse clears the counter. After the gate pulse ends, the first measurement pulse that arrives triggers a latch pulse that loads the new count into the display. If the head has been taken off the shaft, no pulse arrives, no latch pulse is made, and the display keeps the last reading until the next measurement or until the power is switched off. Not given: the clock frequency and gate time. Ours: logic ICs and a seven-segment display.

Materiais para este passo:

Placa de circuito impressoPlaca de circuito impresso1 peça
Cristal de quartzoCristal de quartzo1 peça
Sortido de circuitos integrados lógicosSortido de circuitos integrados lógicos1 divider, AND gate, counter, latch, reset
Acionador de mostrador de sete segmentosAcionador de mostrador de sete segmentos1 peça
Mostrador de sete segmentos de quatro dígitosMostrador de sete segmentos de quatro dígitos1 peça
Fio de soldaFio de solda1 as needed

Ferramentas necessárias:

Ferro de soldarFerro de soldar
4

Power it and measure

Fit the battery and the thumb button as the power switch. Press the contact head against the end of the turning shaft so it turns with it, push the button, and read the revolutions in the window, now or after you take the tachometer away.

Materiais para este passo:

BateriaBateria1 peça
Botão de pressãoBotão de pressão1 peça

Ferramentas necessárias:

Ferro de soldarFerro de soldar

Materiais

15

Ferramentas necessárias

4

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...