Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Trundle-and-Pitman Churn: One Crank Turns the Dasher Staff and Lifts It Up and Down at Once
Martin

Criado por

Martin

9. novembro 2026NO
8
0
0
0
0

Trundle-and-Pitman Churn: One Crank Turns the Dasher Staff and Lifts It Up and Down at Once

Edward L. Dorsey of Greenwood, Indiana, received US 23,556, dated 12 April 1859, for giving a churn's dashers two motions at once. A crank turns a wheel with teeth on its face. The teeth work between the rounds of a trundle (lantern) wheel on the dasher staff and turn it, while a pin on the same wheel works a pitman that lifts and drops the staff. The staff carries a round dasher at its foot and an armed whipping dasher above; the up-and-down dasher keeps the cream from simply swirling round. This rung builds it in wood and steel rod on a square food container.
Intermediário
About 8 hours

Instruções

1

Two motions from one crank

A carregar o notebook Jupyter…
2

A crank that lifts the dasher, before it

Rarey's crank only lifted the dasher. Dorsey's turns it as well, from the same wheel.
3

Read US 23,556

"... the teeth of wheel H work between the rounds n, n, n, of trundle wheel C, and give a circular motion to the said dashers. Thus the staff and dashers have two distinct motions—a vertical reciprocating and a rotary motion."
4

Body A, top and upright B

Use a square food-grade container about 300 x 300 x 320 mm. Cut an 18 mm plywood top 340 mm square with a 24 mm hole in the middle for the staff, and screw two cleats underneath so it sits square on the rim. Screw a hardwood upright B 44 x 44 mm, 300 mm tall, to the top, its near face 110 mm from the hole, and bore it 12.5 mm square to the top, 260 mm above it.

Materiais para este passo:

Recipiente de armazenamento de grau alimentarRecipiente de armazenamento de grau alimentar1 peça
Placa de contraplacadoPlaca de contraplacado1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Parafusos para madeiraParafusos para madeira10 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
5

Wheel H and shaft I

Cut an 18 mm plywood disc 300 mm across. Drill 36 holes 8 mm across, evenly round a 280 mm circle, and glue in 8 mm hardwood dowels standing 16 mm proud of the front face as the teeth. Drill an 8 mm hole 45 mm from the centre and press in an 8 mm steel pin 16 mm proud as pin o. Glue a hardwood hub 60 mm across on the back. Fix a 12 mm stainless rod through hub and disc with an M4 screw across as shaft I, pass it through the upright, and fix a hardwood crank D 132 mm long with a dowel handle on its far end.

Materiais para este passo:

Placa de contraplacadoPlaca de contraplacado1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Parafusos de máquinaParafusos de máquina2 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon2 peças

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
LixaLixa
Conjunto de chaves de fendasConjunto de chaves de fendas
6

Staff E, trundle C and dashers

Cut two hardwood heads M 74 mm across and 6 mm thick, bore each 20 mm in the middle and drill 8 holes 8 mm across on a 62 mm circle; glue in 8 dowel rounds n 116 mm long. Cut a 20 mm hardwood dowel 594 mm long as staff E and drill an 8.5 mm hole across it 14 mm below its top. Cut dasher J, an 18 mm plywood disc 200 mm across with six 28 mm holes, and dasher K, two plywood arms 230 x 24 mm halved into a cross. Glue J on the staff's foot, K 112 mm above it and the trundle where its middle meets the teeth with the staff halfway up its stroke.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Placa de contraplacadoPlaca de contraplacado1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de serras-copoConjunto de serras-copo
GramposGrampos
LixaLixa
7

Pitman F

Bend an 8 mm stainless rod in the vise: a small eye at one end to go on pin o, then a straight length 80 mm from the eye's centre to a right-angle bend, then a leg 56 mm long that goes across through the hole in the staff's top as the pivot. Put the staff in through the top, set the eye on pin o with a washer and lock nut, and push the leg through the staff.

Materiais para este passo:

Varão de aço inoxidávelVarão de aço inoxidável1 peça
Anilha planaAnilha plana1 peça
Porca de segurança com anel de nylonPorca de segurança com anel de nylon1 peça

Ferramentas necessárias:

Torno de bancadaTorno de bancada
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Chave inglesa ajustávelChave inglesa ajustável
8

The build in 3D

FreeCAD model of this build, the near half of the container cut away: the top and upright, wheel H with its dowel teeth and pin o, shaft I and crank D, the pitman bent into the staff's top, trundle C, and dashers K and J. It was checked for clashes at 12 crank positions through a full turn.
Arquivo de designBLENDCC0 - Free
9

Churn

Lift the top, pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and set the top back. Turn the crank steadily and time it: the dashers turn and rise and fall together. When the butter comes, lift the top and staff out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater12 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
10

Troubleshooting

Trundle-and-pitman churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Edward L. Dorsey** of Greenwood, Johnson County, Indiana, US 23,556, 12 April 1859, "Churn". He found it best in a square box, the rising and falling lower dasher checking the swirl the upper one gives. He claimed the trundle wheel, staff, pitman and cog wheel together. He gave no sizes or materials: every size and material here is ours.

Materiais

13

Ferramentas necessárias

18

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...