Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Sealed Screw-Axis Drum Churn: The Dasher's Axis Screws Into It Through a Pipe in the Side, a Sprung Washer Keeps It Tight
Buttercup

Criado por

Buttercup

11. novembro 2026IE
10
0
0
0
0

Sealed Screw-Axis Drum Churn: The Dasher's Axis Screws Into It Through a Pipe in the Side, a Sprung Washer Keeps It Tight

Peter Dunwald of Corning, New York, received US 31,447, dated 19 February 1861, for the shaft of a churn whose perforated dasher turns on a horizontal axis. The axis passes through a pipe set in the churn's side and screws into a socket on the dasher, drawing the dasher tight against the pipe's inner end; at the outer end a washer, pressed by an india-rubber spring inside a cup on the crank, seals the pipe. Unscrew the crank and the dasher comes out for cleaning. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

Two seals from one screw

A carregar o notebook Jupyter…
2

A dasher on a horizontal shaft through the end, two months before

Pike's shaft runs through the end of a box and is set by thumb screws. Dunwald's screws into the dasher and seals itself.
3

Read US 31,447

"By this construction the act of screwing the axis c, into the part 4 draws the dasher tight against the inner end of the pipe 3, and the washer 6, sets with the spring pressure against the other end, keeping the axis water or milk tight. By unscrewing the axis c, the dasher can be removed when required."
4

Print the pipe collars (two)

A collar 40 mm across and 7 thick with a 20.1 mm bore, one each side of the bucket's wall round the pipe 3. Print two. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
5

Print the eye 2

The eye on the inside of the far wall: 40 mm across, 13 thick, with a 12.6 mm hole for the centre 1. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Body a, pipe 3 and eye 2

Use a 20-litre food-grade bucket as the body a. Bore a 20.4 mm hole through one side, 170 mm above the inside floor, and a 12.6 mm hole opposite. Cut a 20 mm stainless tube with a 14 mm bore, 52 mm long, push it through the first hole between the two printed collars so 35 mm stands inside, and seal it all with silicone. Screw the eye 2 inside over the opposite hole with silicone, and seal the hole outside. Cut an HDPE lid to the top.

Materiais para este passo:

Balde de 20 litrosBalde de 20 litros1 peça
Tubo de aço inoxidávelTubo de aço inoxidável1 peça
Filamento PETGFilamento PETG1 peça
Vedante de siliconeVedante de silicone1 peça
Parafusos para madeiraParafusos para madeira4 peças
Chapa de PEADChapa de PEAD1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Conjunto de chaves de fendasConjunto de chaves de fendas
Serra tico-ticoSerra tico-tico
BússolaBússola
7

Print the socket 4

The socket on the dasher's hub: 22 mm across and 30 long with a flange, a 21 mm recess 5.5 deep for the pipe's end, and a hexagon pocket for an M12 nut behind it. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
8

Dasher b with socket 4 and centre 1

Turn two hardwood ends 180 mm across and 20 thick, each with a boss 70 mm across and 20 long on its inner face and a hub 50 mm across standing out 10 mm (pipe side) or 8 mm (far side). Bore eight 15 mm holes through each end on a 120 mm circle. Roll a sheet of stainless 164 mm wide into a drum 180 mm across, drill three rings of twelve 15 mm holes in it, and rivet it round the ends. Bore the pipe-side hub 22 mm, 30 deep, and glue in the socket 4 with an M12 nut pressed into its pocket. Drive a 12 mm stainless pin 40 mm long into the far hub as the centre 1.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Chapa de aço inoxidávelChapa de aço inoxidável1 peça
Rebites cegosRebites cegos24 peças
Porca sextavadaPorca sextavada1 peça
Cola de madeiraCola de madeira1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça

Ferramentas necessárias:

Torno de madeiraTorno de madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Tesoura de chapaTesoura de chapa
Kit de rebitadoraKit de rebitadora
Serra de arco para metaisSerra de arco para metais
9

Print the cylinder 5

The small cylinder on the handle: 32 mm across and 22 long, a 21 mm bore 19 deep for the pipe's end, washer and rubber spring, and a 12.1 mm hole for the axis. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
10

Axis c, washer 6, spring 7 and handle d

Cut a 12 mm stainless rod 93 mm long for the axis c. Thread its inner 15 mm M12 with the die, and turn it down to 10 mm for 8 mm where the washer sits, 24 to 32 mm from its outer end. Cut a stainless washer 6 to 20.6 mm across with a 10.2 mm hole, and a rubber washer 7 13 mm long (squeezed to 11), 20.6 across with a 13 mm hole, from natural rubber sheet. Cut a crank d of mild steel flat bar, 100 mm throw, with a hardwood handle, and bolt the cylinder 5 to it. To assemble: set the dasher in the bucket with its centre in the eye, push the axis through the pipe and screw it into the socket until the dasher is drawn up to the pipe's end; slide on the washer and rubber over the axis's narrow part, then the cylinder and crank, and pin the crank to the axis's end.

Materiais para este passo:

Varão de aço inoxidávelVarão de aço inoxidável1 peça
Anilha planaAnilha plana1 peça
Placa de borracha naturalPlaca de borracha natural1 peça
Barra chata de aço macioBarra chata de aço macio1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
ContrapinoContrapino1 peça
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Jogo de machos e cossinetesJogo de machos e cossinetes
Torno mecânicoTorno mecânico
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
11

The build in 3D

FreeCAD model of this build, the bucket cut open: the pipe through the wall in its collars, the drum dasher with its socket and centre in the eye, the axis screwed into the socket, the washer, rubber spring, cylinder and crank.
Arquivo de designBLENDCC0 - Free
12

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, so it stands below the pipe, and put on the lid. Turn the crank steadily, timing it. When the butter comes, take off the lid, pull the pin and the crank, unscrew the axis and lift the dasher out. Take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater8 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
13

Troubleshooting

Screw-axis churn troubleshooting.

Flow

Loading...
14

History and honest limits

**Peter Dunwald** of Corning, Steuben County, New York, US 31,447, 19 February 1861, "Churn". He claimed "the axis c, provided with the washer 6, kept to the end of the pipe 3, by a spring 7, said axis c, screwing into the socket 4, on the dasher b", and did not claim the revolving dasher on a horizontal shaft. His one figure is printed turned on its side. He does not give the dasher's form beyond "perforated as usual"; ours is a riveted drum, his drawing shows a rounded one. The patent gives no sizes; every size here is ours.

Materiais

20

Ferramentas necessárias

19

Ficheiros de design

5

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...