Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)
Forge

Criado por

Forge

14. novembro 2026NO
9
0
0
0
0

Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)

How smiths made hand hammers and sledges, from George Edwinson's smithing series (Amateur Work, 1886): solid steel, or an iron head with a steel face welded into a slit fork; the eye punched and shaped on two oval taper drifts so the wedged handle cannot work loose. Panes: ball, fuller, wedge and claw.
Avançado
A day at the forge

Instruções

1

His weights

A carregar o notebook Jupyter…
2

Read Edwinson

"To make a steel hammer it is only necessary to get a bar of steel the required size, heat, upset, and forge to the selected size and shape."
3

Solid steel route

Heat a steel bar of the size needed, upset it and forge it to shape. Punch the hole for the handle and work it on a taper drift. Tool the hammer off smoothly at a red heat, then heat it and harden it in water.

Materiais para este passo:

Aço de cadinhoAço de cadinho1 peça

Ferramentas necessárias:

Forja de ferreiroForja de ferreiro
BigornaBigorna
MarretaMarreta
Tenazes de ferreiroTenazes de ferreiro
Mandril de alargar furoMandril de alargar furo
Balde de têmperaBalde de têmpera
4

Steel-faced route: weld the face

Upset a stout iron bar if it is too thin. Slit one end hot with a hot chisel (his sett) into a fork. Forge a steel bar to a wedge that fits it. Bring the iron to a welding heat and the steel to its own (a separate fire if needed), roll the steel in calcined borax and weld. Reheat with the steel protected by welding mixture or sand, and finish the weld.

Materiais para este passo:

Barra de ferro forjadoBarra de ferro forjado1 peça
Barras de aço empoladoBarras de aço empolado1 peça
Bórax em póBórax em pó1 peça
AreiaAreia1 peça

Ferramentas necessárias:

Forja de ferreiroForja de ferreiro
Talhadeira a quenteTalhadeira a quente
BigornaBigorna
MarretaMarreta
Tenazes de ferreiroTenazes de ferreiro
5

Shape the head

Cut off the steel, forge steel and iron up into the face. Fashion the head and pane, punch the handle hole and form it on a taper drift, cut the hammer off the bar and finish it held in crooked bit tongs. If both ends are to be steel, weld in both before cutting off. Panes: ball for riveting, fuller for spreading iron, wedge, or claw for drawing nails.

Ferramentas necessárias:

Forja de ferreiroForja de ferreiro
Mandril de alargar furoMandril de alargar furo
Talhadeira a quenteTalhadeira a quente
BigornaBigorna
MarteloMartelo
Tenazes de ferreiroTenazes de ferreiro
6

Shape the eye on two drifts

Use two oval taper drifts: one tapered all round to form the lower side of the eye, the other tapered only on its long sides for the upper part. The eye tapers from both sides across the head, but only from the lower side lengthwise. Round the edges on the underside.

Ferramentas necessárias:

Forja de ferreiroForja de ferreiro
Mandril de alargar furoMandril de alargar furo
BigornaBigorna
MarteloMartelo
7

Sizes and sledges

Hand hammers usually weigh 1-2 lb (0.45-0.9 kg). Larger fuller or wedge pane hammers of 3-30 lb are sledges; one-handed sledges weigh 3-5 lb; heavier ones get stout ash handles 3-4 ft (0.9-1.2 m) long for two hands.

Ferramentas necessárias:

BigornaBigorna
8

Hang the head

Drive the handle into the eye from below so its end is compressed and fits tight. Cut off the extra wood, split the end with a chisel and drive in a wedge of well-seasoned wood. If the eye tapers two ways, cross-slit and drive two wedges.

Materiais para este passo:

Tarugo de freixoTarugo de freixo1 peça
Cunhas de madeiraCunhas de madeira1 peça

Ferramentas necessárias:

Faca de dois cabosFaca de dois cabos
FormõesFormões
MarteloMartelo
9

Troubleshooting

Hammer troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" (part X), **Amateur Work, Illustrated**, vol. VI (Ward, Lock & Co., 1886-87), pp. 211-214 (checked on the archive.org scan amateurworkillus06lond), pp. 212-214 and figs. 227-235. He gives no temper for the face; the metric figures and tools are ours.

Materiais

7

Ferramentas necessárias

10

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...