ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Electricity From the Wind: The Cube Law and a Rotor on a Dynamo
Volt

Criado por

Volt

27. setembro 2026SE
5
0
0
0
0

Electricity From the Wind: The Cube Law and a Rotor on a Dynamo

For a thousand years windmills ground grain and pumped water. In the winter of 1887–88 Charles F. Brush put one to a new job in the back garden of his house in Cleveland, Ohio: a 17-metre rotor of 144 cedar blades turning a dynamo that charged a cellar full of batteries — electricity from the wind. Everything about a wind generator follows from one relation: the power in the wind goes with the cube of its speed and the square of the rotor's diameter. That is why turbines grew huge and why their sites are chosen with such care. This rung builds a small wind generator from a hobby motor and a printed rotor, measures its power in front of a fan at several wind speeds, and checks the cube law.
Iniciante
About 4 hours

Instruções

1

The cube law

A carregar o notebook Jupyter…
2

Build a small wind generator

A small permanent-magnet DC motor is also a generator: turn its shaft and it makes a voltage proportional to speed. Print a three-bladed rotor 300 mm across in PETG, with a hub that presses onto the motor shaft, each blade twisted — steep near the hub, flatter towards the tip — because the tip moves faster through the air than the root. Mount the motor on a dowel mast clamped to a plywood base, with the rotor facing the fan. Wire the motor's terminals to a 330 Ω resistor as a load, with the multimeter across it. Add an LED in series if you want to see it light.

Materiais para este passo:

Hobby Motor - GearHobby Motor - Gear1 peça
Filamento PETGFilamento PETG60 g
Cavilhas de madeira duraCavilhas de madeira dura1 conjunto
Placa de contraplacadoPlaca de contraplacado1 folha
Resistência de 330 ohmResistência de 330 ohm1 peça
LED de 5 mmLED de 5 mm1 peça
Fios de ligaçãoFios de ligação1 conjunto

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Jogo de chaves AllenJogo de chaves Allen
3

Measure its power at three wind speeds

Stand the box fan 1.5 m away, facing the rotor. Measure the wind speed at the rotor with the anemometer before fitting the rotor, at each fan setting. Fit the rotor, run the fan, and read the voltage across the resistor once it is steady. The electrical power is **V² ÷ R**. Record wind speed and power for each fan setting. Plot power against wind speed cubed. It should be roughly a straight line — not exactly, because a small motor's own losses take a bigger share at low speed. Then divide your power by the notebook's power passing through a 0.3 m disc at the same wind speed. That ratio is your rotor's power coefficient, and the Betz rung shows the most it could ever be.

Ferramentas necessárias:

Ventoinha de caixa (velocidade variável)Ventoinha de caixa (velocidade variável)
Anemómetro portátilAnemómetro portátil
MultímetroMultímetro
Fita métricaFita métrica
Tacómetro digitalTacómetro digital
4

History and context

**Charles F. Brush, Cleveland, Ohio, 1887–88** — a 17 m, 144-bladed rotor on a tower about 18 m (60 ft) high driving a 12 kW dynamo through step-up gearing, charging batteries that lit his house; it ran for some twenty years. Brush had already built the arc-lighting dynamo in this catalogue. No patent number is asserted here. In Denmark from 1891, **Poul la Cour** tested rotors in a wind tunnel of his own and found that fewer blades turning faster made better use of the wind than many slow ones — the direction every modern turbine took. **Honest limits.** The wind stops; a wind generator needs storage or another source behind it. Its output swings with the cube of a quantity that changes by the minute. And a large rotor is a serious hazard: it must be able to stop itself in a storm, as the Halladay windmill's governor in this catalogue already could.

Materiais

7

Ferramentas necessárias

9
Total estimado
O que quem fez comprou. Os materiais sem preço obtêm-se onde os comprares.
R$13.07

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...