Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Counter-Turning Cylinder Churn: The Ribbed Cylinder Turns One Way While the Dashers Inside Turn the Other
Edwin Ward of New York received US 27,175, dated 14 February 1860, for a churn. A horizontal cylinder with ribs inside turns on bearings while a shaft through it, carrying dashers, turns the other way: one crank drives both, the cylinder through a pair of pinions on a tube round a short fixed shaft and a toothed ring on its head. He reports butter "in from three to five minutes".
The patent gives no sizes; every size here is ours.
Avançado
About 3 days, plus printing
Instruções
1
1
One crank, two directions
One crank, two directions
A carregar o notebook Jupyter…
2
2
Dashers turning inside a still barrel, two months before
Dashers turning inside a still barrel, two months before
Rohrer's barrel stands still round the turning dashers. Ward turns the cylinder too, the other way.
3
3
Read US 27,175
Read US 27,175
"Now it will readily be seen that whenever rotation is given to the shaft that it and the dashers will traverse in one direction and that the cylinder and slats will traverse in a contrary direction, and that the velocity of the one in relation to that of the other will depend upon the number of teeth and comparative diameter of the pinions and the toothed surface on the head of the cylinder."
4
4
Print the crown wheel j
Print the crown wheel j
Crown wheel, 60 teeth on its face, module 2, with a hub bored 16.4 mm for the shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the toothed ring o
Print the toothed ring o
Crown ring, 120 teeth on its face, module 2, 258 mm across, to screw to the cylinder's head. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the pinions k and n
Print the pinions k and n
Spur pinion, 12 teeth, module 2, bored 12.6 mm to turn on the fixed shaft l. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Cylinder a with ribs d and door p
Cylinder a with ribs d and door p
Cut two hardwood heads 364 mm across from 25 mm board, each with a hub 50 mm across bored 17 mm on the axis, the geared head's hub 38 mm long. Bend 1.5 mm stainless sheet into a shell 360 mm across inside and 450 long, screw it to the heads with silicone sealant, and screw four hardwood ribs 30 x 30 mm, 450 long, inside it a quarter turn apart. Cut a door 140 x 160 mm in the shell, hung on two small hinges and closed with a hook. Screw the printed toothed ring to the geared head's face.
Materiais para este passo:
Tábua de madeira de lei2 peças
Chapa de aço inoxidável2 peças
Parafusos para madeira40 peças
Parafusos de máquina8 peças
Dobradiça de livro para móvel2 peças
Colchete (macho e fêmea)1 peçaFerramentas necessárias:
Bússola
Serra tico-tico
Tupia
Tesoura de chapa
Berbequim sem fios
Jogo de brocas
Conjunto de brocas de pá
Sargento de barra
Conjunto de chaves de fendas8
8
Shaft f, dashers g and crank h
Shaft f, dashers g and crank h
Cut a 16 mm stainless shaft 662 mm long. Screw four hardwood dashers 430 x 122 x 16 mm to hardwood blocks pinned on it, a quarter turn apart, reaching 140 mm from the axis, and pass it through the heads' hubs. Fit the crown wheel on the geared end and a crank 160 mm long with a handle beyond it.
Materiais para este passo:
Varão de aço inoxidável1 peça
Tábua de madeira de lei1 peça
Cavilhas de madeira dura1 peça
Cola de madeira1 peça
Shaft Collar2 peças
Filamento PETG1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra de mesa
Serra de arco para metais
Limas (lima de mão)
Berbequim sem fios
Jogo de brocas
Lixa9
9
Frame c, bearings b, fixed shaft l and standard m
Frame c, bearings b, fixed shaft l and standard m
On a base board stand a post with a hardwood bearing block bored 51 mm for the plain head's hub. At the geared end stand a hardwood standard m, and fix a 12 mm stainless rod l upright in its top, running up into a second bearing block for the geared hub just outside the toothed ring. On l, below the shaft, slide the two pinions joined by a short stainless tube: the upper one meshing the crown wheel j, the lower the toothed ring o. Hold them with collars.
Materiais para este passo:
Madeira macia de 70x70 mm1 peça
Tábua de madeira de lei2 peças
Varão de aço inoxidável1 peça
Tubo de aço inoxidável1 peça
Shaft Collar2 peças
Sortido de parafusos sextavados4 peças
Porca de segurança com anel de nylon4 peçasFerramentas necessárias:
Serra de mesa
Conjunto de brocas de pá
Berbequim sem fios
Jogo de brocas
Serra de arco para metais
Chave inglesa ajustável
Fita métrica10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the cylinder cut through the middle: the ribs and four dashers, the shaft and crank, the crown wheel and toothed ring facing each other across the upright fixed shaft with its two pinions, the bearings, post and standard on the base.
11
11
Churn
Churn
Turn the door uppermost, pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and close it. Turn the crank steadily, timing it: the patent says three to five minutes. When the butter comes, turn the door down over a bowl, let the buttermilk run out, take out the butter, wash it in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater12 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável12
12
Troubleshooting
Troubleshooting
Counter-turning churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Edwin Ward** of New York, US 27,175, 14 February 1860, "Churn". He claimed the horizontal cylinder with ribs and an interior shaft with dashers, made to turn in opposite directions. His bevel pinions and the toothed surface on the head are here printed crown gears and pinions, and his fixed shaft l is upright, carrying the geared end's bearing. The patent gives no sizes; every size here is ours.
Materiais
19- 2 peçasReferência
- 2 peçasReferência
- 1 peçaReferência
- 40 peçasReferência
- 8 peçasReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- Referência
- 1 peçaReferência
- Referência
- Referência
- 12 lReferência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
20- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
4Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Atmospheric Barrel Churn: Reversed Concave Dashers Close to the Staves, Fresh or Warmed Air Piped to the Middle
por Buttercup
Marcenaria
6
0
0
0
0
0

Diagonal-Blade Shouldered-Breaker Churn: Pitched Blades on Uneven Arms Turn Under the Shoulders of Two Breakers
por Buttercup
Marcenaria
4
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

