Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Pendulum Churn: A Treadle Swings the Hung Churn, Arms From the Base Plunge the Dasher and a Twisted Strip Turns It
Buttercup

Criado por

Buttercup

11. novembro 2026IE
5
0
0
0
0

Pendulum Churn: A Treadle Swings the Hung Churn, Arms From the Base Plunge the Dasher and a Twisted Strip Turns It

W. B. Gordinier of Coudersport, Pennsylvania, received US 28,170, dated 8 May 1860, for a pendulum churn. The churn stands in a frame that hangs like a swing and is set swinging with a treadle and a cord over a pulley. Arms from the base hold the dash rod's cross head, so as the swing moves the dasher plunges up and down, while a twisted strip on the rod, working through a slotted bar, turns it back and forth. The patent gives no sizes; every size here is ours.
Avançado
About 3 days

Instruções

1

Why the dasher plunges as the churn swings

A carregar o notebook Jupyter…
2

A spiral that turns a push into a spin, one week before

Ashley slides a nut on a spiral to spin his beater. Gordinier slides his twisted strip through a slot.
3

Read US 28,170

"From this description it will be seen that the mechanism for operating the churn gives to the parts a combined vibrating, reciprocating, and alternate rotary motion, which are obtained by simply moving the treadle L."
4

Base A, standards B and cross bar B'

From pine lumber 60 x 50 mm make a base 1600 x 660 mm with four cross pieces, one under the pivot. Stand two standards 60 x 60 mm at the middle of the long sides, 1350 mm tall, joined at the top by a cross bar B'. Bore them 25 mm across 1300 mm above the floor for a 24 mm stainless pivot shaft, with the pulley J loose on its middle.

Materiais para este passo:

Madeira de pinhoMadeira de pinho4 peças
Parafusos para madeiraParafusos para madeira40 peças
Cola de madeiraCola de madeira1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
RoldanaRoldana1 peça
Shaft CollarShaft Collar2 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
5

Swing frame C, cross bar H and churn box E

Hang two hardwood hangers 90 x 30 x 60 mm on the pivot shaft, 400 mm apart, and fix two 20 mm hardwood dowels upright under each, 60 mm apart centre to centre, reaching 1150 mm down to a hardwood bottom board 440 x 440 x 25 mm. Across the arms 400 mm below the pivot fix a hardwood bar H with a slot 28 x 7 mm in its middle. Screw a 20-litre bucket to the board and cut a 28 mm hole in its lid's centre.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Cavilhas de madeira duraCavilhas de madeira dura4 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira16 peças
Balde de 20 litrosBalde de 20 litros1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
6

Cross head D, dash rod D', strip G and arms F

Cut a hardwood cross head 28 x 40 mm, 504 long, notched at each end to run between a pair of arm rods, with a hardwood roller 36 mm across on a pin at each end. Bore its middle 21 mm. Cut a 20 mm stainless dash rod, cut a groove round it and hold it in the cross head with two key collars in the groove, so it turns; fix a hardwood dasher, two crossed boards 220 x 60 x 16 mm with four 20 mm holes, 410 mm below the cross head. Twist a stainless strip 25 x 3 mm, 300 long, a quarter turn every 90 mm in the vise, fix it to the rod's top and pass it up through bar H's slot. Cut two mild steel flat bar arms F with holes 640 mm apart; bolt one end of each to a bracket on the base under the pivot, 60 mm up, and the other to the cross head's end.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Shaft CollarShaft Collar2 peças
Chapa de aço inoxidávelChapa de aço inoxidável1 peça
Barra chata de aço macioBarra chata de aço macio2 peças
Parafuso de carroçariaParafuso de carroçaria4 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon4 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Serra de arco para metaisSerra de arco para metais
Tesoura de chapaTesoura de chapa
Torno de bancadaTorno de bancada
Limas (lima de mão)Limas (lima de mão)
Chave inglesa ajustávelChave inglesa ajustável
7

Treadle L and cord K

Hinge a hardwood treadle 600 x 240 x 25 mm to a block on the base beyond the churn. Tie a cord to each end of the cross head, bring both up to the pulley J, take them over it together and down to the treadle's far end.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Dobradiça de livro para móvelDobradiça de livro para móvel2 peças
Parafusos para madeiraParafusos para madeira8 peças
CordelCordel1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
8

The build in 3D

FreeCAD model of this build, swung 12 degrees: the base and standards, the swing frame with its bottom board and the bucket cut open, the cross head between the arm rods, the arms F from the base, the dash rod and dasher, the twisted strip through bar H, the pulley J on the pivot shaft, the cord and the treadle.
Arquivo de designBLENDCC0 - Free
9

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket and put on its lid. Work the treadle with your foot in time with the swing, timing it, so the churn swings up to about 20 degrees each way. When the butter comes, stop the swing, unbolt the arms F from the cross head and lift the dash rod out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater10 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
10

Troubleshooting

Pendulum churn troubleshooting.

Flow

Loading...
11

History and honest limits

**W. B. Gordinier** of Coudersport, Potter County, Pennsylvania, US 28,170, 8 May 1860, "Churn" (the drawing spells the name Gordnier). He claimed the swinging frame carrying the churn, with the arms F, spiral plate G, cord K, pulley J and treadle L. He does not explain how the arms make the dasher rise and fall; the working above is ours. Every size is ours.

Materiais

18

Ferramentas necessárias

17

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...