Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Harness Straps: Cut Along the Hide With Compass and Round Knife (or Plough), Edges Finished With Bone (Hasluck, 1904)
Tex

Criado por

Tex

14. novembro 2026FO
6
0
0
0
0

Harness Straps: Cut Along the Hide With Compass and Round Knife (or Plough), Edges Finished With Bone (Hasluck, 1904)

How a harness maker cuts and finishes straps, from P. N. Hasluck's Harness Making (1904): marked along the hide with an 8 ft straightedge or a compass, cut with the round knife on a cutting-board (or with a plough gauge, 1/2 to 5-1/2 in), always along the hide, then the edges knocked, trimmed with the spokeshave, scraped, sanded and polished with gum and a smooth bone.
Iniciante
About 1 hour

Instruções

1

Widths

A carregar o notebook Jupyter…
2

Read Harness Making

"Straps are always cut along the hide and not across it, the hide being much stronger lengthways."
3

Lay out

Lay the side on the bench with the back toward you. Mark straight lines with a blunt-pointed awl or seat-awl against a straightedge at least 8 ft long, without cutting the grain. Do not cut lower into the hide than the strap's width; cut shaped pieces from patterns.

Materiais para este passo:

Couro para arreiosCouro para arreios1 peça

Ferramentas necessárias:

Régua de traçarRégua de traçar
Sovela de enchimento de seleiroSovela de enchimento de seleiro
4

Cut

With the round knife: set the compass to the width, run one point along the edge and draw it toward you to leave a line, then cut from the right-hand end on a cutting-board, holding the leather steady with the left hand. With the plough: set the knife on the gauge (1/2 to 5-1/2 in) with the thumb-screw, hold the leather flat and press it forward with the guard tight to the edge. Cut reins first, then traces, back-bands and the rest; linings from the belly.

Ferramentas necessárias:

Compasso de riscar de seleiroCompasso de riscar de seleiro
Faca para couroFaca para couro
Tábua de corteTábua de corte
5

Finish the edges

Knock the edges along to consolidate them, trim them round and level with the spokeshave, run a glass scraper over them and sandpaper. For brown work, wipe with a thin solution of gum and water and rub with brown paper and a smooth bone to a polish. For black, dye, rub dry with a rag, and polish with brown paper and bone.

Materiais para este passo:

Goma-arábicaGoma-arábica1 peça
Papel pardoPapel pardo1 peça
LixaLixa1 peça

Ferramentas necessárias:

Plaina de raspar curvasPlaina de raspar curvas
Casco de vidroCasco de vidro
Dobradeira de ossoDobradeira de osso
MarteloMartelo
6

Troubleshooting

Strap troubleshooting.

Flow

Loading...
7

History and honest limits

From Paul N. Hasluck, **Harness Making** (1904) (checked on the archive.org scan harnessmaking00hasl, pp. 12, 42-44). Using broken glass (cullet) as the glass scraper, the tools and the metric figures are ours.

Materiais

4
  • Referência
  • Referência
  • Referência
  • 1 peça
    Referência

Ferramentas necessárias

9

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...