Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Saddle Crupper: Slit Body, Buckled Billet and Paper-Cored Dock (Hasluck, Saddlery, 1904)
Tex

Criado por

Tex

13. novembro 2026FO
2
0
0
0
0

Saddle Crupper: Slit Body, Buckled Billet and Paper-Cored Dock (Hasluck, Saddlery, 1904)

A saddle crupper runs from the back of a riding saddle to a padded loop (the dock) under the horse's tail, so the saddle cannot slide forward. This is the full-sized saddle crupper from Paul N. Hasluck's Saddlery (1904): a slit leather body, a buckled billet, and a dock shaped over string and wet brown paper. Every size is his.
Intermediário
About 1 day

Instruções

1

His sizes in centimetres

A carregar o notebook Jupyter…
2

Read Saddlery, ch. V

"Full-sized saddle cruppers (Fig. 9), which are used to prevent the saddle from advancing too much, are made about 1 in. wide, and sometimes a little more."
3

Cut the body

Cut the body about 1 in wide (or a little more) and about 1 ft 6 in long. Slit one end for about 5 in and turn the other end in for a 7/8 in buckle. Shave the points of the slits and the end of the chape.

Materiais para este passo:

Couro para arreiosCouro para arreios1 peça

Ferramentas necessárias:

Faca para couroFaca para couro
Fita métricaFita métrica
4

Make the billet and set the buckle

Cut a billet as wide as the buckle and 2 ft 4 in long; trim one end for the buckle and shave the other. Edge both pieces, polish the edges and crease them with a hot checker. Put on the buckle and stitch the billet: the first stitch by the buckle goes over the edge and through chape and billet together, the next through the loop. Run four or five stitches towards the point on each side, and come back to the buckle on the other side, making the last stitch over the side the same as the opposite side.

Materiais para este passo:

Couro para arreiosCouro para arreios1 peça
Fivela de ferro com fuzilhãoFivela de ferro com fuzilhão1 peça
Fio de linhoFio de linho1 peça
Cera de abelhaCera de abelha1 peça

Ferramentas necessárias:

Faca para couroFaca para couro
Biselador de bordosBiselador de bordos
Brunidor de bordos de couroBrunidor de bordos de couro
DobradeiraDobradeira
Maçarico a propanoMaçarico a propano
SovelaSovela
Duas agulhas de correeiroDuas agulhas de correeiro
Torno de seleiroTorno de seleiro
5

Put on the loop

Put a loop on the flat lower down the body, about 6 in from the buckle, stitching it across at each end.

Materiais para este passo:

Couro para arreiosCouro para arreios1 peça
Fio de linhoFio de linho1 peça
Cera de abelhaCera de abelha1 peça

Ferramentas necessárias:

Faca para couroFaca para couro
Forma de passadoresForma de passadores
SovelaSovela
Duas agulhas de correeiroDuas agulhas de correeiro
6

Shape the dock core

The dock is much smaller round than a gig crupper dock. Take a piece of string about 1 ft long and roll wet brown paper round it until it is the thickness you need in the middle; thin the ends by cutting the paper before damping it.

Materiais para este passo:

FioFio1 peça
Papel pardoPapel pardo1 peça

Ferramentas necessárias:

TesouraTesoura
EsponjaEsponja
Fita métricaFita métrica
7

Cover the dock

Cut the dock leather about 1 ft 1 in long; it must be soft and pliable, so damp it before stitching. Stitch it over the core as it is, without cutting a groove, drawing it very tightly over the paper. Dry the dock and finish it in shape.

Materiais para este passo:

Couro para arreiosCouro para arreios1 peça
Fio de linhoFio de linho1 peça
Cera de abelhaCera de abelha1 peça

Ferramentas necessárias:

Faca para couroFaca para couro
EsponjaEsponja
SovelaSovela
Duas agulhas de correeiroDuas agulhas de correeiro
Torno de seleiroTorno de seleiro
8

Join the dock and punch the billet

Stitch the dock to the slits with a splice of about 1-1/4 in. Put about a dozen holes in the billet, and vary the lengths to suit the size of horse.

Materiais para este passo:

Fio de linhoFio de linho1 peça
Cera de abelhaCera de abelha1 peça

Ferramentas necessárias:

Faca para couroFaca para couro
SovelaSovela
Duas agulhas de correeiroDuas agulhas de correeiro
Vazador para couroVazador para couro
9

Troubleshooting

Saddle crupper troubleshooting.

Flow

Loading...
10

History and honest limits

From **Saddlery**, edited by Paul N. Hasluck, David McKay, 1904 (archive.org saddlery00hasl), chapter V, "Saddle Cruppers, Breastplates, and Other Accessories", saddle cruppers, pp. 40-41, Fig. 9; every fraction was read on the scan. He does not say how the billet fastens to the saddle; check against Fig. 9 and your saddle. The thread, tools and metric figures are ours.

Materiais

6

Ferramentas necessárias

13

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...