Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Craftsman Leather Billfold: Two Cardboard Patterns, Silk Lining and Saddle-Stitched Waxed Silk (Boy Mechanic, 1919)
Tex

Criado por

Tex

13. novembro 2026FO
12
0
0
0
0

Craftsman Leather Billfold: Two Cardboard Patterns, Silk Lining and Saddle-Stitched Waxed Silk (Boy Mechanic, 1919)

Livingston Haviland's billfold from The Boy Mechanic, Book 3 (1919): two leather body parts cut to stiff-cardboard patterns (13-1/4 and 8-3/16 by 4-1/4 in), lined with skiver or silk moire, folded into two card pockets and a money compartment, glued, and hand-sewn with heavy waxed silk 3/16 in from the edges.
Intermediário
About 1 day

Instruções

1

His patterns in centimetres

A carregar o notebook Jupyter…
2

Read The Boy Mechanic, Book 3

"The making of a billfold is easily within the range of an amateur in leather work, who will observe the instructions carefully." Seal, morocco, pigskin and ooze sheep are all satisfactory.
3

Cut the patterns and the leather

Cut two patterns of stiff cardboard (Fig. 1). Body part No. 1: 13-1/4 by 4-1/4 in, with fold lines at 2-1/2, 2-5/8, 3, 2-5/8 and 2-1/2 in, and each end (A, B) cut in with 1/2 in radius arcs, set in 1/4 in. Body part No. 2: 8-3/16 by 4-1/4 in, with fold lines at 2-19/32, 3 and 2-19/32 in. Lay each pattern on the leather and trim the leather even with it, guiding the knife with a metal straightedge, on a close-grained hardwood board or a piece of sheet zinc.

Materiais para este passo:

Couro de porcoCouro de porco1 peça
Moldes de cartãoMoldes de cartão1 peça

Ferramentas necessárias:

LápisLápis
RéguaRégua
Régua de traçarRégua de traçar
X-ato (faca de precisão)X-ato (faca de precisão)
Tábua de madeira de leiTábua de madeira de lei
Chapa de zincoChapa de zinco
4

Line the parts

Cut linings slightly larger than the patterns. Skiver is glued all over with a good, pliable leather glue that will not crack the leather; smooth it on gently without stretching, or the leather may buckle, and dry it under a light weight. Silk moire is glued with a thin stripe round the edges only, left to overhang, and trimmed off neatly when dry.

Materiais para este passo:

Tecido de sedaTecido de seda1 peça
Cola para couroCola para couro1 peça

Ferramentas necessárias:

TesouraTesoura
X-ato (faca de precisão)X-ato (faca de precisão)
5

Glue and fold

Fold part No. 1 to form the back and the two card pockets. Apply stripes of glue as shown in Fig. 3, drop part No. 2 (the money compartment) into place, and fold the ends of No. 1 over on the dotted lines. Weight the billfold and let the glue dry.

Materiais para este passo:

Cola para couroCola para couro1 peça

Ferramentas necessárias:

Modelador de couroModelador de couro
6

Mark and punch the stitching

Draw a straight line with a blunt-point tool along the edges to be sewn, 3/16 in from them. Mark the stitch spacing for an inch on a strip of paper and transfer it along the line. Punch the holes on a pine board with a diamond-pointed awl held vertical (D); back the open ends with strips of cardboard while punching.

Ferramentas necessárias:

Modelador de couroModelador de couro
RéguaRégua
Sovela de pespontarSovela de pespontar
Tábua de pinhoTábua de pinho
Moldes de cartãoMoldes de cartão
7

Sew and finish the edges

Sew with heavy waxed silk matching the leather, by hand or with the work clamped between two boards. Thread a needle on each end, start both from the right side (E), pass the needle from the first hole through the second (F) and, with the needles in position (G), continue this stitch. Tie the ends neatly. Trim the edges and tool them smooth with a suitable metal tool or rod, heated moderately, applying water with the fingertip.

Materiais para este passo:

Linha de sedaLinha de seda1 peça
Cera de abelhaCera de abelha1 peça

Ferramentas necessárias:

Duas agulhas de correeiroDuas agulhas de correeiro
TesouraTesoura
X-ato (faca de precisão)X-ato (faca de precisão)
Barra redonda de aço macioBarra redonda de aço macio
8

Troubleshooting

Billfold troubleshooting.

Flow

Loading...
9

History and honest limits

From "A Craftsman Leather Billfold" by Livingston Haviland, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 446-447). He does not give the number of stitches to the inch or what waxes the silk (beeswax is ours). Pigskin is one of his four leathers. The tools and metric figures are ours.

Materiais

6

Ferramentas necessárias

13

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...