Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Tooled Calfskin Card Case: Folded Pockets, Lined Centre and a Border Design (Boy Mechanic, 1915)
Tex

Criado por

Tex

13. novembro 2026FO
7
0
0
0
0

Tooled Calfskin Card Case: Folded Pockets, Lined Centre and a Border Design (Boy Mechanic, 1915)

Mary C. Scovel's card case (The Boy Mechanic, Book 2, 1915): a 10 by 4-3/4 in pattern folded in the middle, with 2 in turned in at each end to make the pockets, tooled on one of the wide panels, lined at the centre with skiver or silk, and sewn at top and bottom.
Iniciante
About 3 hours

Instruções

1

Her pattern in centimetres

A carregar o notebook Jupyter…
2

Read The Boy Mechanic, Book 2

Her outfit: "two special tools costing 50 cents each, one with a narrow edge for lining patterns, and one with broad ends for tooling; and a piece of tin, plate glass, or very smooth hard wood, which should not be smaller than 9 by 12 in. A soft sponge, a triangle, a rule, tracing paper and a hard pencil are also needed." Russian calfskin is best for tooling and stamping.
3

Make the paper pattern

Take paper 10 by 4-3/4 in and fold it in the middle, 5 in each side, then fold in 2 in at each outside edge toward the centre to make the pockets (a longer paper and deeper fold for deeper pockets). Cut the leather to the pattern with at least 1/4 in margin.

Materiais para este passo:

Couro de vitelaCouro de vitela1 peça

Ferramentas necessárias:

Papel vegetalPapel vegetal
LápisLápis
TesouraTesoura
RéguaRégua
4

Line out the folds

Damp the leather on the rough side. Lay the folded paper on the right side and, with ruler, triangle and lining tool, draw the vertical lines where it is to fold at the centre and at each pocket, and line all round the four sides. There are now four panels, two wide and two narrow.

Ferramentas necessárias:

EsponjaEsponja
RéguaRégua
Esquadro de desenhoEsquadro de desenho
Modelador de couroModelador de couro
5

Damp the leather and transfer the design

Draw the whole design for the front (one of the wide panels) on tracing paper. Wet the leather on the wrong (unfinished) side with a soft sponge: pat it to moisten, not soak, it; too wet and the tool sticks and leaves an uneven background. Pin the design firmly on the leather, tack the leather down on its outer margin to the glass or board, and go over every line with a hard pencil, with firm, even pressure. Lift the paper and go over the lines with the narrow lining tool, with a strong, firm stroke. A line design can stop here.

Materiais para este passo:

Couro de vitelaCouro de vitela1 peça

Ferramentas necessárias:

EsponjaEsponja
Papel vegetalPapel vegetal
LápisLápis
Pioneses (caixa de 50)Pioneses (caixa de 50)
Placa de vidroPlaca de vidro
Modelador de couroModelador de couro
6

Tool or stamp the background

Leave at least 1/8 in between the edge of the pattern and the design. To tool, press the background down with the broad end in even, long strokes; if it will not go down, the leather is too dry, so take it off and damp the back again. Keep the edges sharp between pressed and raised parts. To stamp instead, strike a small carpenter's nail set lightly with a wooden mallet in rows of circles; too hard a blow cuts the leather.

Ferramentas necessárias:

Modelador de couroModelador de couro
Puncionador de pregosPuncionador de pregos
Maço de madeiraMaço de madeira
EsponjaEsponja
7

Line, fold and sew

Line only the two centre rectangles, with skiver leather or silk cut about 1/16 in less at top and bottom and 1/4 in wider on each side. Leather: paste its back with library paste, smooth it down and dry it under a heavy weight. Silk: paste only about 1/4 in round its edges, and weight it. Fold the case and sew it at top and bottom; cut off the surplus leather about 1/8 in from the stitches. Stitch on a sewing machine with a long stitch, a large needle and silk as heavy as the needle takes; try it on a scrap first, and put tissue paper over the leather if the foot marks it. Without a machine, prick holes with an awl and sew with needle and silk, running or over-and-over; going over-and-over to the end and back gives an X stitch.

Materiais para este passo:

Tecido de sedaTecido de seda1 peça
Cola de farinha de trigoCola de farinha de trigo1 peça
Linha de sedaLinha de seda1 peça

Ferramentas necessárias:

TesouraTesoura
Máquina de costuraMáquina de costura
SovelaSovela
Duas agulhas de correeiroDuas agulhas de correeiro
X-ato (faca de precisão)X-ato (faca de precisão)
8

Troubleshooting

Card case troubleshooting.

Flow

Loading...
9

History and honest limits

From Mary C. Scovel, "Arts-Crafts Leather Work", in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 432-441), Part II. The tools and metric figures are ours.

Materiais

4

Ferramentas necessárias

15

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...