Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Spiral-Edge Countersinks: One Curved Slot Up the Cone Makes an Edge That Slices Instead of Scraping (Laursen, 1926)
Forge

Criado por

Forge

13. novembro 2026NO
6
0
0
0
0

Spiral-Edge Countersinks: One Curved Slot Up the Cone Makes an Edge That Slices Instead of Scraping (Laursen, 1926)

Laust K. Laursen of College Station, Texas, received US 1,586,559, dated 1 June 1926. Ordinary countersinks have straight edges in radial planes, which press on the wood all at once and scrape it, like pushing a knife straight down on a loaf. Laursen curved the edge into a spiral running up and out from near the point, ahead of the radial line as the tool turns. It reaches the wood a little at a time and slices, leaving a smooth countersink without chatter. His simplest form is one curved slot in the cone, its leading edge sharpened and the cone behind it relieved. We make a set of three in tool steel. The patent gives no sizes; every size here is ours.
Intermediário
About 1 day

Instruções

1

Why a spiral edge shears

A carregar o notebook Jupyter…
2

Read US 1,586,559

"In this particular form the spiral extends outwardly in the direction of action, that is to say, the usual direction of rotation of a countersink is clockwise, viewed from the top, or counterclockwise, as viewed from the bottom." "It has been found that a hole formed with a countersink as shown in Figs. 1 and 2 will be very smooth and uniform on the inside."
3

Turn the blanks

From octagonal tool steel turn three blanks: a 90 degree cone 3 to a point, 12, 16 and 20 mm across at its base, then the body 1 and an 8 mm shank 2 50 mm long with three filed flats. Heat each to a cherry red and let it cool slowly in the air to soften it.

Materiais para este passo:

Barra octogonal de aço para ferramentasBarra octogonal de aço para ferramentas2 peças

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Goiva de sangrarGoiva de sangrar
TransferidorTransferidor
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
Jogo de limasJogo de limas
ForjaForja
Tenaz de forjaTenaz de forja
Óculos de segurançaÓculos de segurança
4

File the spiral slot 4

Blue the cone and scribe a spiral on it from 1 mm from the point to the rim, turning a quarter of the way round, leaning ahead in the direction the tool turns (clockwise seen from the shank). File a slot along it with a round needle file, 2 to 3 mm wide and 1.5 mm deep at the rim, shallower towards the point. Sharpen the slot's leading edge 5 and file the cone behind it slightly lower, so only the edge touches the work.

Ferramentas necessárias:

Jogo de limas de agulhaJogo de limas de agulha
Morsa de máquinaMorsa de máquina
Jogo de limasJogo de limas
5

Harden and temper

Heat each head to a cherry red, until a magnet no longer sticks, and quench it point first in water, moving it about. Rub it bright with a stone, heat the shank gently 20 mm behind the head, and quench again as soon as a light straw colour reaches the cutting edge.

Ferramentas necessárias:

ForjaForja
Tenaz de forjaTenaz de forja
Íman pequenoÍman pequeno
Balde de têmperaBalde de têmpera
ÁguaÁgua
Pedra de amolarPedra de amolar
Luvas de soldadorLuvas de soldador
Óculos de segurançaÓculos de segurança
6

Hone and test

Hone the edge lightly with the stone. Drill screw holes in hardwood and countersink them: the edge should cut a smooth bell with no chatter and throw curled shavings out of the slot.

Ferramentas necessárias:

Pedra de amolarPedra de amolar
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Tábua de madeira de leiTábua de madeira de lei
Óculos de segurançaÓculos de segurança
7

Troubleshooting

Spiral countersink troubleshooting.

Flow

Loading...
8

History and honest limits

**Laust K. Laursen** of College Station, Texas, US 1,586,559, dated 1 June 1926, filed 1 August 1925. He set out to give a countersink "a cutting blade or edge so arranged that it will tend to cut, rather than scrape, the work", each edge curving spirally of the tool. He shows three forms: one slot in a hollow head, two split halves with twin edges, and a many-bladed one he found better for metal; we make the first, in one piece. He gives no sizes or angle; our 90 degree cones, quarter-turn spiral and the house hardening are ours.

Materiais

1

Ferramentas necessárias

20

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...