Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Leave-In Probe Thermometer: Stainless Probe on a Flexible Lead to a Programmable Timer (Chapman, US 6,568,848, 2003)
Penny

Criado por

Penny

3. novembro 2026DK
5
0
0
0
0

Leave-In Probe Thermometer: Stainless Probe on a Flexible Lead to a Programmable Timer (Chapman, US 6,568,848, 2003)

A meat thermometer you leave in the roast. A pointed stainless steel probe stays in the meat. A flexible lead runs out of the oven to a battery timer unit with a display, keys and a beeper. You pick the meat and how well done you want it; the unit shows the temperature and the time left, and beeps when it is done. Result: continuous reading of the inside of the meat without opening the oven. Source: P. A. Chapman and C.-A. Chang (Maverick Industries), US 6,568,848 (2003). The patent's main form sends the readings by radio; it also states this wired form. Unknown: the sensor, the circuit, the target temperatures and the materials. Picture: the patent drawing.
Intermediário
Unknown

Instruções

1

Make the probe

Make the probe of a rigid material such as stainless steel. It has a pointed end that goes into the meat, a straight section from the point, then a curved section to the other end. The temperature sensor sits inside. Not given: the type of sensor, sizes.

Materiais para este passo:

Tubo de termómetro com tampão pontiagudoTubo de termómetro com tampão pontiagudo1 stainless steel
Sensor de temperaturaSensor de temperatura1 peça

Ferramentas necessárias:

Dimensões desconhecidasDimensões desconhecidas
Ferro de soldarFerro de soldar
2

Fit the flexible lead and plug

Join a flexible lead to the curved end of the probe, so the probe can lie at any angle to the unit. Put a plug with a male end on the other end of the lead. Not given: the lead material, the plug type, the length.

Materiais para este passo:

Cabo multicondutorCabo multicondutor1 flexible lead
Conector desconhecidoConector desconhecido1 plug
Fio de soldaFio de solda1 as needed

Ferramentas necessárias:

Ferro de soldarFerro de soldar
Dimensões desconhecidasDimensões desconhecidas
3

Build the timer unit

In a hand-held case, fit a microprocessor that runs the cooking programs, a liquid crystal display, a beeper and batteries. Fit nine keys: clock or timer, probe A or B, meat type, doneness, two to set and change the final temperature, hours, minutes, and start/stop. Add a jack for each probe, a stand to set it upright and a clip for a belt or pocket. Not given: the circuit, the program, the case material.

Materiais para este passo:

Placa de circuito impressoPlaca de circuito impresso1 peça
Circuito integradoCircuito integrado1 microprocessor
Visor LCD de segmentosVisor LCD de segmentos1 peça
Botão de pressãoBotão de pressão9 keys
Besouro piezoelétricoBesouro piezoelétrico1 peça
Conector desconhecidoConector desconhecido2 probe jacks
BateriaBateria1 as needed
Material desconhecidoMaterial desconhecido1 case, stand, clip
Fio de soldaFio de solda1 as needed

Ferramentas necessárias:

Ferro de soldarFerro de soldar
Conjunto de chaves de fendasConjunto de chaves de fendas
4

Roast with it

Plug the probe into the timer unit. Pick the meat (beef, veal, lamb, pork, chicken, turkey) and the doneness (rare, medium rare, medium, well-done); the patent cooks to USDA guidelines. Push the probe into the meat, put it in the oven and lead the cable out to the unit, then press start. The display shows the meat, the doneness, the temperature (°F or °C) and the time left, and the beeper sounds at the right moments. A second probe watches a second piece. Not given: the temperature for each doneness.

Ferramentas necessárias:

FornoForno

Materiais

12

Ferramentas necessárias

4

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...