Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Magnetic-Field Press: Soft-Steel Punches as the Poles (Cochardt, US 3,412,461, 1968)
Emma

Criado por

Emma

3. novembro 2026SE
13
0
0
0
0

Magnetic-Field Press: Soft-Steel Punches as the Poles (Cochardt, US 3,412,461, 1968)

A press that lines magnetic powder up while it squeezes it. Two punches of magnetically soft steel close a die, and two coils around them make the punches the poles of an electromagnet. The field runs straight through the powder from one punch face to the other. Result: a press for anisotropic magnets, about 4000 oersted in the pressing space. Source: A. W. Cochardt, US 3,412,461 (1968). Unknown: the die's metal, sizes, coil windings, the press and the pump. Picture: the patent drawing.
Avançado
Unknown

Instruções

1

Make the punches and the die

Make an upper and a lower press member (punches) of magnetically soft steel. Then the magnetic gap is only the thickness of the part being pressed. Make a die wall that the punches close to form a flat cavity. A wide, thin cavity keeps the field lines straight; they bend only at its edges. Ours: mild steel for the punches. Not given: the die's metal, sizes.

Materiais para este passo:

Barra redonda de aço macioBarra redonda de aço macio1 upper and lower punches
Metal desconhecidoMetal desconhecido1 die

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Dimensões desconhecidasDimensões desconhecidas
2

Wind the two coils

Wind two coils to sit around the punches, one above the die and one below, so that together they drive a field along the pressing direction. The patent's coils were water-cooled. Ours: enamelled copper wire. Not given: the turns, the wire size, how the cooling water runs.

Materiais para este passo:

Fio de cobre esmaltadoFio de cobre esmaltado1 two coils

Ferramentas necessárias:

ÁguaÁgua
Dimensões desconhecidasDimensões desconhecidas
3

Mount it in a press

Mount the punches, die and coils in a press, so the upper punch and the die can move down together while the lower punch stays put. Connect the coils to a current supply. Ours: a hydraulic press and a DC supply. Not given: the press, the supply.

Ferramentas necessárias:

Prensa hidráulicaPrensa hidráulica
Fonte de alimentação de corrente contínuaFonte de alimentação de corrente contínua
4

Press a plate in the field

Raise the lower punch, lower the upper punch into the die, and pump in a ferrite slurry: water with 1 to 2 percent dispersing agent. Move the upper punch and die down to press the slurry and drive out the water, and energise the coils at the same time, to about 4000 oersted. A plate 0.5 x 10 x 9 cm took 8200 watts. Demagnetise the plate as far as possible, then raise the punch, lower the die and lift the plate off the lower punch. Ours: a diaphragm pump.

Ferramentas necessárias:

Bomba de diafragmaBomba de diafragma
Fonte de alimentação de corrente contínuaFonte de alimentação de corrente contínua
ÁguaÁgua

Materiais

3

Ferramentas necessárias

6

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...