Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Forged Square-Neck Door Bolt and Nut, Threaded with a Screw-Plate (Moxon, 1677)
Forge

Criado por

Forge

14. novembro 2026NO
9
0
0
0
0

Forged Square-Neck Door Bolt and Nut, Threaded with a Screw-Plate (Moxon, 1677)

Joseph Moxon's 1677 way to make the screw bolt for a door: a square iron bar forged down to a square neck and round pin, the head cut off with a chisel, the pin threaded with a screw-plate, and a punched iron nut threaded with a tap. The square neck sits in a square hole so the bolt cannot turn while the nut is tightened.
Intermediário
About an hour per bolt

Instruções

1

Choosing the hole

A carregar o notebook Jupyter…
2

Read Mechanick Exercises

"The Shank of the Screw for Doors and many other purposes must be Forged square near the Head, because it must be let into a square hole that it may not twist about when the Nut is turned about hard upon the Screw-Pin."
3

Forge the square neck

Take a square iron bar as near the size of the head as you can. At a flame (white) heat lay the shank length flat on the near side of the anvil and hammer it down to thickness; do not strike over the edge or you cut the iron. Reheat, turn it, and hammer the other two sides close up to the head.

Materiais para este passo:

Barra de ferro forjadoBarra de ferro forjado1 peça

Ferramentas necessárias:

Forja de ferreiroForja de ferreiro
BigornaBigorna
MarteloMartelo
Tenazes de ferreiroTenazes de ferreiro
4

Round the pin, cut the head

Hammer down the corners of the part meant for the thread and round it. Set the chisel at the head thickness, strike half through, turn and cut each side half through until it comes off. Square the shoulder: reheat, grip in square-nosed tongs, set the shank in the vice with the shoulder on the jaws, and hammer the head.

Ferramentas necessárias:

Forja de ferreiroForja de ferreiro
Talhadeira de bigornaTalhadeira de bigorna
Tenazes de ferreiroTenazes de ferreiro
Torno de bancada pesadoTorno de bancada pesado
MarteloMartelo
5

Punch the nut

Forge a nut blank from the bar. Harden the point of a steel punch of the hole's size (no tempering: the hot iron softens it). At a blood-red heat punch from one side until the far side bulges, turn it, set it flat, and punch through over the hole of a bolster. Dip the punch in water whenever it changes colour. Let forged work cool on the floor or hearth; never quench it.

Materiais para este passo:

Barra de ferro forjadoBarra de ferro forjado1 peça

Ferramentas necessárias:

Forja de ferreiroForja de ferreiro
BigornaBigorna
Punção a quentePunção a quente
MarteloMartelo
Balde de têmperaBalde de têmpera
Tenazes de ferreiroTenazes de ferreiro
6

Thread the pin

File the shank and head, file the pin round, and taper its end by the depth of the screw-plate's threads. Find the screw-plate hole the pin just slides through, turn the pin in it, and file off the marks it cuts: the pin is then true. Set the bolt head down in the vice, press the next smaller hole (groove diameter equal to the pin) hard down on it, and turn the plate evenly.

Ferramentas necessárias:

Limas (lima de mão)Limas (lima de mão)
Torno de bancada pesadoTorno de bancada pesado
Jogo de machos e cossinetesJogo de machos e cossinetes
7

Tap the nut

Fit the tap to the round hole of the nut; it must match the pin (try it in the same screw-plate hole). Set the nut flat in the vice and turn the tap hard round by its handle, or by the square hole near the screw-plate handle, until it cuts the thread.

Ferramentas necessárias:

Torno de bancada pesadoTorno de bancada pesado
Jogo de machos e cossinetesJogo de machos e cossinetes
8

Troubleshooting

Screw bolt troubleshooting.

Flow

Loading...
9

History and honest limits

From Joseph Moxon, **Mechanick Exercises, or the Doctrine of Handy-Works** (1677), Smithing, Numb. I pp. 10-11 and Numb. II pp. 29-31 (checked on the archive.org scan mechanickexercis00moxo). He gives no sizes or nut shape; the metric example and the tool heads are ours.

Materiais

1

Ferramentas necessárias

10

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...