Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Turner's Pole Lathe with Puppets, Screw Centre and Treadle (Moxon, 1680)
Woody

Criado por

Woody

14. novembro 2026NO
7
0
0
0
0

Turner's Pole Lathe with Puppets, Screw Centre and Treadle (Moxon, 1680)

The workshop pole lathe of Joseph Moxon's Mechanick Exercises: legs and twin cheeks bolted square, sliding puppets wedged through the bed, a fixed steel-pointed pike and an adjustable screw centre, a hinged treadle with a cross-treadle, and a fir pole pinned to the ceiling for the spring.
Avançado
Two to three days

Instruções

1

His sizes

A carregar o notebook Jupyter…
2

Read Mechanick Exercises

"The Lathe is described in Plate 12. A. This Machine is so vulgarly known..."
3

Legs and cheeks

Set up two legs about 2 ft 10 in (86 cm) high, plumb, each with a tenon on top as thick as the gap you want between the two cheeks. Lay a cheek each side of the tenons, level, and fix them: pinned, or better with an iron bolt whose square neck sits in a square hole in the near cheek, drawn up by a nut. Brace legs and cheeks to the floor and walls so nothing trembles.

Materiais para este passo:

Tábua de carvalho-brancoTábua de carvalho-branco1 peça
Parafuso de carroçariaParafuso de carroçaria1 peça

Ferramentas necessárias:

SerroteSerrote
Formão de samblagemFormão de samblagem
Maço de madeiraMaço de madeira
Arco de pua e brocaArco de pua e broca
4

Puppets

Make two (or two or three pairs of) square puppets, strong rather than weak and as short as your work allows: the centres must stand a little more than half the work's diameter above the cheeks. Give each a tenon at the foot that slides in the gap between the cheeks, with a mortise through it below the cheeks for a tapering wedge, driven with a mallet to clamp the puppet down.

Materiais para este passo:

Tábua de carvalho-brancoTábua de carvalho-branco1 peça
Cunha de madeira duraCunha de madeira dura1 peça

Ferramentas necessárias:

SerroteSerrote
Formão de samblagemFormão de samblagem
Maço de madeiraMaço de madeira
5

Pike and screw centre

Near the top of one puppet fix a strong iron pike with a tempered steel point. Through the other fit an iron screw in a nut in the puppet, also with a steel point, both points in one straight line facing each other. Put an iron handle 7-8 in long with a knob at each end through the screw head. Cut the puppets to square shoulders just below the pikes to carry the rest.

Materiais para este passo:

Barra de ferro forjadoBarra de ferro forjado1 peça
Barra quadrada de aço para ferramentasBarra quadrada de aço para ferramentas1 peça

Ferramentas necessárias:

Forja de ferreiroForja de ferreiro
BigornaBigorna
Jogo de machos e cossinetesJogo de machos e cossinetes
Balde de têmperaBalde de têmpera
6

Rest and oil horn

Make the rest a square piece 1-1.5 in thick, 2-2.5 in broad, a little longer than the gap between the puppets. Hang a horn tip down on the outside of the right-hand puppet near the top, filled with oil, with a wooden cover and button carrying an iron wire that reaches nearly to the bottom, to oil the centre holes.

Materiais para este passo:

Tábua de carvalho-brancoTábua de carvalho-branco1 peça
Chifre de bovinoChifre de bovino1 peça
Arame de ferroArame de ferro1 peça
Óleo de máquinaÓleo de máquina1 peça

Ferramentas necessárias:

SerroteSerrote
Arco de pua e brocaArco de pua e broca
7

Treadle and cross-treadle

Make a treadle about 2.5 in broad, 1 in thick and 3 ft (up to 4 ft) long. Nail its back end to the floor with a piece of leather, 1-1.5 ft behind the lathe and midway between the legs, so the front reaches 1.5-2 ft past the front of the lathe. Cut a square notch 1.5 in wide and 2 in long in the far end for winding the string. Fix an iron pin about 0.5 in thick, standing 1.5-2 in up, in the middle; under the cheeks fix a cross-treadle with a row of holes 2-3 in apart to take the pin.

Materiais para este passo:

Tábua de carvalho-brancoTábua de carvalho-branco1 peça
Correia de couroCorreia de couro1 peça
Pregos de ferroPregos de ferro1 peça
Barra de ferro forjadoBarra de ferro forjado1 peça

Ferramentas necessárias:

SerroteSerrote
MarteloMartelo
Arco de pua e brocaArco de pua e broca
8

Pole and string

Use a fir pole, thick or thin to suit the work; if it is too stiff, thin its upper and under sides with a draw-knife. Pin the thick end to a ceiling timber with one nail so it pivots. About a foot away nail two cheeks to the joists with a batten across their foot to carry the pole. Run the string from the pole's thin end, round the work, to the treadle.

Materiais para este passo:

Vara de madeiraVara de madeira1 peça
CordelCordel1 peça
Pregos de ferroPregos de ferro1 peça
Tábua de carvalho-brancoTábua de carvalho-branco1 peça

Ferramentas necessárias:

Faca de dois cabosFaca de dois cabos
MarteloMartelo
9

Troubleshooting

Pole lathe troubleshooting.

Flow

Loading...
10

History and honest limits

From Joseph Moxon, **Mechanick Exercises**, Numb. X, Turning (1680), pp. 176-185 and Plate 12 (checked on the archive.org scan mechanickexercis00moxo). He gives no sizes for cheeks, puppets or pole; metric and the wood choices are ours.

Materiais

12

Ferramentas necessárias

10

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...