Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Plastic Extruder: Steam-Jacketed Screw Stuffer with a Heated Nozzle (Andersen & Strasdin, US 2,384,521, 1945)
Emma

Criado por

Emma

3. novembro 2026SE
7
0
0
0
0

Plastic Extruder: Steam-Jacketed Screw Stuffer with a Heated Nozzle (Andersen & Strasdin, US 2,384,521, 1945)

A screw extruder for thermoplastics: a turning screw in a steam-jacketed barrel pushes hot, softened plastic forward through a short nozzle heated electrically. The barrel is kept a little below the plastic's flow temperature and the nozzle well above it, so the extruded rod comes out with a smooth, glass-like skin. Result: an extruder that makes rod, tube or strip at 25 to 30 feet a minute. Source: B. Andersen and R. F. Strasdin (Celanese), US 2,384,521 (1945). Unknown: sizes and metals. Picture: the patent drawing.
Avançado
Unknown

Instruções

1

Make the screw

Turn a screw to fit the barrel. Its thread may be single or double; to press the plastic harder toward the nozzle, make the pitch increase or the groove get shallower toward that end. Example: a double-thread screw. Ours: mild steel. Not given: sizes.

Materiais para este passo:

Barra redonda de aço macioBarra redonda de aço macio1 screw

Ferramentas necessárias:

Torno mecânicoTorno mecânico
FresadoraFresadora
Dimensões desconhecidasDimensões desconhecidas
2

Make the jacketed barrel

Make the barrel with a steam jacket round it and a steam port into the jacket, and a feed throat at the back end. The inside wall may be grooved, pitched so that every flight of the screw always meets a groove; this stops the plastic slipping. Not given: the metal, the steam pressure.

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 barrel and jacket

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Dimensões desconhecidasDimensões desconhecidas
3

Fit the heated nozzle

At the front, fit a streamlined nozzle head so no plastic can pocket and decompose, and a nozzle 1/2 to 18 inches long; about 6 inches in the example. Perforated plates may go between the screw and the nozzle. Heat the nozzle with an electric resistance coil. Ours: nichrome wire.

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 nozzle head and nozzle
Fio de nicrómioFio de nicrómio1 nozzle heating coil
Material isolante desconhecidoMaterial isolante desconhecido1 coil insulation

Ferramentas necessárias:

Torno mecânicoTorno mecânico
4

Drive the screw

Drive the screw through a gear from a motor, so its speed can be kept steady; 20 revolutions a minute in the example. Not given: the drive.

Materiais para este passo:

Motor elétricoMotor elétrico1 drive motor
Metal desconhecidoMetal desconhecido1 drive gears

Ferramentas necessárias:

Dimensões desconhecidasDimensões desconhecidas
5

Extrude a rod

Keep the barrel 0 to 100 °F below the plastic's flow temperature and the nozzle 50 to 100 °F above it. Example: barrel at about 270 °F by steam, nozzle at about 400 °F, for a cellulose acetate with a flow temperature of 307 °F. Feed the hot, softened plastic into the throat at a steady rate. Carry the rod away on a conveyor and cool it at once with cold water, then cut it to length.

Ferramentas necessárias:

Caldeira a vaporCaldeira a vapor
PirómetroPirómetro
ÁguaÁgua

Materiais

5

Ferramentas necessárias

6

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...