Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Steam Boiler: Small Brass Shell Boiler, Screwed and Soldered (Hopkins, Model Engines and Small Boats, 1898)
Volt

Criado por

Volt

3. novembro 2026SE
12
0
0
2
0

Steam Boiler: Small Brass Shell Boiler, Screwed and Soldered (Hopkins, Model Engines and Small Boats, 1898)

A small steam boiler for model engines and boats: a brass cylinder 4 in across, closed by two brass heads tied together by a brass stay rod, its seam held by two rows of brass screws and sealed with solder. It sits in a russia-iron jacket over an alcohol lamp, with a weighted safety valve and fusible plugs that put the lamp out if the water runs low. Result: a strong little shell boiler, 6 to 12 in long to suit the engine. Source: N. M. Hopkins, Model Engines and Small Boats (1898), ch. III. Unknown: the working pressure and the valve's sizes. Picture: the book's Fig. 33.
Intermediário
Unknown

Instruções

1

Make the heads and stay

Cut two brass disks 4 in across and about 1/8 in thick, each with a 1/4 in hole in the centre, and true them up in the lathe. Pass a 1/4 in brass rod through both and solder it, with plenty of solder inside the heads to make them steam-tight. Screw heavy brass disks (round nuts are better than square) onto the rod ends against the heads. Set the heads 10 in apart over their outsides; about 6 in will do for a small single-acting engine, 7 in for a double engine, up to 12 in for a larger one.

Materiais para este passo:

Barra redonda de latãoBarra redonda de latão1 two heads, two nuts
Varão de latãoVarão de latão1 1/4 in stay
Solda de estanho-chumboSolda de estanho-chumbo1 as needed
FluxoFluxo1 as needed

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Bico de BunsenBico de Bunsen
2

Roll and screw the shell

Cut soft sheet brass at least 1/32 in thick (1/16 in for boilers over 8 in long), about 14 in long and 1/2 in longer than the heads so it overhangs 1/4 in each end. Roll it round the heads on tinner's rollers, never by hand, so it laps about 1 in. Slip it over the heads and rod and bind it tight with heavy twine. Drill two rows of holes along the lap, tap them and turn in little brass screws that go just through the under plate without projecting. Do not use iron screws: their rust pits the seams.

Materiais para este passo:

Chapa de latãoChapa de latão1 shell
Parafusos de máquinaParafusos de máquina1 small brass screws
Fio de atarFio de atar1 binding

Ferramentas necessárias:

Calandra de chapaCalandra de chapa
Berbequim de mãoBerbequim de mão
Jogo de machos e cossinetesJogo de machos e cossinetes
3

Solder it up

Push the heads and rod out, hold the shell in a Bunsen flame and run solder well along the seam. Push the heads back and solder them all round the edge, and screw the nuts tight: the screws and stay take the strain, the solder keeps in the steam. Drill two or three 1/4 in holes in the top and bush them with heavy brass disks soldered on. For fusible plugs, drill two 1/4 in holes near the bottom and solder them shut with little brass caps.

Materiais para este passo:

Solda de estanho-chumboSolda de estanho-chumbo1 as needed
FluxoFluxo1 as needed
Barra redonda de latãoBarra redonda de latão1 bushes and plug caps

Ferramentas necessárias:

Bico de BunsenBico de Bunsen
Berbequim de mãoBerbequim de mão
4

Fit the jacket and safety valve

Cut end supports from russia sheet iron to hold the boiler by its ends, with an opening for the alcohol lamp, and bend a russia-iron cover over it, riveted to the ends by little ears. Punch a row of small holes along the cover's lower edge to let air in for the lamp; the cover keeps in the heat and keeps draughts off the flame. Turn a small safety valve true in the lathe, grind it to its seat with emery and oil, and fit a lead weight on its bar. Not given: the valve's sizes.

Materiais para este passo:

Chapa de ferro da RússiaChapa de ferro da Rússia1 ends and cover
Rebites de ferroRebites de ferro1 small
Barra redonda de latãoBarra redonda de latão1 valve
ChumboChumbo1 weight

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Jogo de rebitarJogo de rebitar
Torno mecânicoTorno mecânico
Pano de esmerilPano de esmeril
5

Fire and set it

Fill the boiler two-thirds full, connect the engine and light the alcohol lamp under it. If the valve blows off before the engine turns over, move the weight a little farther out until the engine runs without steam escaping; well made, the valve will then blow off soon after the engine stops if the fire is left. If the water ever runs very low, the fusible plugs melt and the steam puts out the lamp. Do not try to burst a boiler to test it.

Ferramentas necessárias:

Lamparina de álcoolLamparina de álcool

Materiais

10

Ferramentas necessárias

9

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...