Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Spiral-Beater Box Churn: Diamond-Holed and Hollow-Ended Beaters Drive the Cream End to End
Buttercup

Criado por

Buttercup

9. novembro 2026IE
9
0
0
0
0

Spiral-Beater Box Churn: Diamond-Holed and Hollow-Ended Beaters Drive the Cream End to End

Harry and Royal V. Robie of Eaton, New York, received US 22,090, dated 16 November 1858, for a box churn with beaters set spirally on a level crank shaft. Every other beater has a diamond hole; the rest have a hollow (concave) end. All are narrow where they join the shaft, so the cream passes between them, and they drive it from one end of the box to the other. A chamber under the box, with a hinged door, holds something cold or warm to bring the cream to temperature. This rung builds it with a food-grade container in a pine body and printed beaters.
Intermediário
About 6 hours, plus printing

Instruções

1

Beaters, spacing and fill

A carregar o notebook Jupyter…
2

Pierced dashers, before it

Farrington broke the cream on the holes of swinging dashers. The Robies pierce every other beater on a turning shaft.
3

Read US 22,090

"... the base of said beaters being made small and narrow where they enter the shaft in order to form an opening for the passage of the cream, between each of the beaters, while the holes in each alternate beater form another passage".
4

Print the beater B

Beater B, with the diamond hole. Print four. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Arquivo de designSTLCC0 - Free
5

Print the beater C

Beater C, with the hollow end. Print three. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Arquivo de designSTLCC0 - Free
6

Print the crank

The crank arm. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Arquivo de designSTLCC0 - Free
7

Print the collar

The collar that holds the shaft's far end. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Arquivo de designSTLCC0 - Free
8

Body and chamber

Use a food-grade container 400 x 280 mm inside and 250 mm deep, with a rim. From 18 mm pine cut two ends 362 x 750 mm with a 120 mm arch at the foot, two sides 444 x 630 mm, two rails 444 x 40 mm and a shelf 444 x 326 mm. Screw the sides between the ends, the rails inside the sides 3 mm below the top, and the shelf 200 mm up. Cut a 360 x 272 mm opening in the front side above the shelf and hang a 356 x 268 mm pine door in it on two butt hinges along its bottom edge.

Materiais para este passo:

Tábua de pinhoTábua de pinho3 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira40 peças
Dobradiça de livroDobradiça de livro2 peças
Parafuso para madeira n.º 8 x 1"Parafuso para madeira n.º 8 x 1"8 peças

Ferramentas necessárias:

SerroteSerrote
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
GramposGrampos
LixaLixa
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
9

Shaft A and beaters

Hang the container by its rim on the rails. Drill a 17 mm hole through both pine ends and both container ends, 150 mm above the container's inside floor. Cut the stainless tube (16 mm) to 574 mm and push it through. Slide on the seven beaters, B, C, B, C, B, C, B, 50 mm apart from the middle out, each a quarter turn round from the last, all blades turned the same way, and fix each with an M4 screw across hub and shaft. Fit the collar on the far end and the crank on the near end with M4 screws, and glue a 12 mm dowel 114 mm long into the crank as the handle.

Materiais para este passo:

Recipiente de armazenamento de grau alimentarRecipiente de armazenamento de grau alimentar1 peça
Filamento PETGFilamento PETG1 peça
Tubo de aço inoxidávelTubo de aço inoxidável1 peça
Parafusos de máquinaParafusos de máquina9 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon9 peças
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Corta-tubosCorta-tubos
Limas (lima de mão)Limas (lima de mão)
Conjunto de chaves de fendasConjunto de chaves de fendas
Chave inglesa ajustávelChave inglesa ajustável
10

The build in 3D

FreeCAD model of this build: the pine body with its arched ends, the chamber door, the container on its rails, the shaft with seven spiral beaters, the collar and the crank.
Arquivo de designBLENDCC0 - Free
11

Churn

Bring the cream to about 15 °C: in warm weather set a tray of ice in the chamber under the box, in cold weather a tray of warm water, and shut the door. Pour in about 12 litres of heavy cream, keeping it 20 mm below the shaft, and check it with the thermometer. Turn the crank steadily and time it. When the butter comes, lift the container out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater12 l
Gelo picadoGelo picado2 kg
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
12

Troubleshooting

Spiral-beater churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Harry Robie** and **Royal V. Robie** of Eaton, Madison County, New York, US 22,090, 16 November 1858, "Churn". They knew beaters set spirally round a level shaft were old, and claimed only the diamond-holed beater B with the hollow-ended beater C and the passage under their narrow bases. They gave no sizes or materials and no number of beaters: ours are seven at 50 mm and a quarter turn apart, blades turned 30 degrees. Their box (Fig. 1) has a rounded floor; our container is flat.

Materiais

15

Ferramentas necessárias

16

Ficheiros de design

5

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...