Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Atmospheric Barrel Churn: Reversed Concave Dashers Close to the Staves, Fresh or Warmed Air Piped to the Middle
Henry Rohrer of Strasburg township, Pennsylvania, received US 26,377, dated 6 December 1859, for improvements to the common barrel churn, which he named the "Champion atmospheric churn". Four concave, tapering dashers run close to the staves with their wide and narrow ends alternating, so they rub as well as beat. Two tubes through the rear head let fresh air into the middle and steam and musty air out; in winter a funnel-mouthed pipe set near a hot stove brings warm air instead.
The patent gives no sizes; every size here is ours.
Intermediário
About 2 days, plus printing
Instruções
1
1
Rohrer's temperatures, and the dashers' sweep
Rohrer's temperatures, and the dashers' sweep
A carregar o notebook Jupyter…
2
2
Air into the cream, three weeks before
Air into the cream, three weeks before
Clow pumped air in at the bottom. Rohrer lets it in by pipes alone, warmed from the stove when needed.
3
3
Read US 26,377
Read US 26,377
"The concaved, tapering sides of the dashers with the wide end of the one followed by the narrow end of the other in its revolutions, produces side eddies as well as being beaten and partially retained by the concaved side; thus a thorough mixing is produced, while a constant supply of fresh air is admitted through the pipe G to the center of the churn"
4
4
Print the step F
Print the step F
A raised open step 80 x 80 mm and 55 mm deep, open at the sides, with a 17 mm socket for the rear pivot. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Barrel A, base B and hatch
Barrel A, base B and hatch
Use a wooden barrel about 450 mm long inside, 320 mm across at the heads. Cut a 120 mm hatch in the bilge with a hardwood lid. Bore the front head 17 mm in its centre for the shaft. Bore the rear head 21 mm in its centre for tube K and 21 mm 120 mm above it for tube I. Make a cradle of two shaped hardwood saddles on a base board so the barrel lies level. Fill the barrel with water overnight so it swells tight, then empty it.
Materiais para este passo:
Barril de madeira1 peça
Tábua de madeira de lei2 peças
Cola de madeira1 peça
Parafusos para madeira12 peçasFerramentas necessárias:
Serra tico-tico
Bússola
Berbequim sem fios
Conjunto de brocas de pá
Serra de mesa
Sargento de barra
Fita métrica
Água6
6
Dashers D and crosses E
Dashers D and crosses E
Shave four hardwood dashers 400 mm long, tapering from 70 to 35 mm wide, with a 20 mm deep concave face on the inner side and the outer edge left straight. Make two crosses of hardwood 15 x 24 mm, 290 mm across, and screw the dashers to their ends, outer edges 150 mm from the centre, the wide ends alternately at the front and the rear. Fix the front cross on a 16 mm stainless shaft through the front head with a crank C outside, and a 16 mm pivot on the rear cross's centre.
Materiais para este passo:
Tábua de madeira de lei2 peças
Parafusos para madeira16 peças
Varão de aço inoxidável1 peça
Shaft Collar2 peças
Cavilhas de madeira dura1 peça
Cola de madeira1 peçaFerramentas necessárias:
Plaina de raspar curvas
Serra de mesa
Berbequim sem fios
Jogo de brocas
Serra de arco para metais
Limas (lima de mão)
Conjunto de chaves de fendas
Lixa
Fita métrica7
7
Step F, tubes I and K, pipes G and H
Step F, tubes I and K, pipes G and H
Screw the printed step over the rear head's centre hole, its socket on the axis. Seal two 20 mm stainless tubes, 70 mm long, through the rear head: K in the centre under the step, I above it. Make the atmospheric pipe G: an upright stainless tube open at its top, joined to I and K by short tubes and elbows. For winter make pipe H: a stainless funnel, mouth m, on a tube to K, with a tee on the tube from I open as the vent l; set the funnel near a warm stove, never on it, and use silicone tube for the joints.
Materiais para este passo:
Tubo de aço inoxidável2 peças
Funil de aço inoxidável1 peça
Parafusos para madeira4 peças
Filamento PETG1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra de arco para metais
Limas (lima de mão)
Maçarico a propano
Torno de bancada
Luvas resistentes ao calor
Conjunto de chaves de fendas8
8
The build in 3D
The build in 3D
FreeCAD model of this build, the barrel, heads and cradle cut through the middle: the four alternately reversed dashers on their two crosses, the shaft and crank, the step F on the rear head over tube K, tube I, and the atmospheric pipe G outside. The frame was turned through a quarter turn.
9
9
Churn
Churn
Fill the barrel about half full with heavy cream, about 15 litres. Bring it to 15-18 °C, checked with the thermometer; in winter put pipe H on with its funnel near the warm stove, otherwise pipe G. Close the hatch and turn the crank steadily, timing it. When the butter comes, open the hatch, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater15 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável10
10
Troubleshooting
Troubleshooting
Atmospheric barrel churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Henry Rohrer** of Strasburg township, Lancaster County, Pennsylvania, US 26,377, 6 December 1859, "Churn". He knew of other ways of bringing air to cream, and claimed the tubes I, K in the rear head with the pipes G and H, mouth m, partition l and tubes L, M, with the dashers D on an open step F. He says he "tested in my own buttery to my entire satisfaction". The patent gives no sizes; every size here is ours. His temperatures, 60 to 65 °F, are 15.6 to 18.3 °C.
Materiais
15- 1 peçaReferência
- 2 peçasReferência
- 2 peçasReferência
- 32 peçasReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 15 lReferência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
22- 1 vendor sell this, none ship to you yetReferência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
2Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Contrary Hinged-Dasher Air-Pump Churn: Two Crossing Dashers Fold to Gather, a Pump Blows Air Through the Cream
por Buttercup
COMIDA E BEBIDAS
4
0
0
0
0
0

Double Rotary Crag Churn: Two Shafts of Four-Edged Arms Turn Through Each Other in Twin Half-Cylinders
por Buttercup
Marcenaria
10
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

