Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Spiral-Corrugated Water-Jacket Churn: A Bevelled Strip Dasher Throws Cream Against Diagonal Corrugations in a Warmed or Cooled Chamber
David Sherman of Uniontown, Maryland, and Robert W. Fenwick of Washington, D.C., received US 29,445, dated 31 July 1860, for a churn whose chamber is a nearly round metal plate corrugated diagonally all over, set in a water-tight wooden case with room around it for warm or cold water. A cranked dasher of two bevelled end bars carries strips standing across the corrugations; it flings the cream against them, they break its current, and it runs back to the middle.
The patent gives no sizes; every size here is ours.
Intermediário
About 3 days
Instruções
1
1
Spiral corrugations from four printed rings
Spiral corrugations from four printed rings
A carregar o notebook Jupyter…
2
2
Churning inside a water jacket, a year before
Churning inside a water jacket, a year before
Gissinger stands two churns in a water box. Sherman and Fenwick wrap the water round one corrugated chamber.
3
3
Read US 29,445
Read US 29,445
"It is a very essential thing to force the cream against a surface which will break the direction of the current and at the same time allow the cream to flow back to the point from which is was moved, for by breaking the current, the churning is facilitated. Our diagonally or spirally corrugated churning chamber does this perfectly."
4
4
Print the chamber rings (four)
Print the chamber rings (four)
One ring of the chamber B: 100 mm long, a plain 208 mm cylinder outside, 28 spiral corrugations inside (crests 95 mm, troughs 101 mm from the axis), open over the top with two upright lips. Print four; they are identical and their corrugations run on from one to the next. Needs a 220 mm bed. PETG, 0.2 mm layers, 30 % infill, 4 walls, printed standing on an end.
5
5
Case A and chamber B
Case A and chamber B
Glue up two hardwood ends 30 x 290 x 288 mm. On each, 160 mm above the bottom edge, draw circles 203 and 209 mm across and rout a groove 6 mm deep between them, with two straight grooves 4 mm wide rising from it to the top edge, about 125 mm apart between centres, for the lips. Cut hardwood sides 20 x 288 x 400, a bottom and a top 20 x 250 x 400, and cut a mouth 122 mm wide the length of the top. Seal the four rings end to end with silicone, set their ends and lips in the grooves with silicone, and glue and screw the case together round them, sealing every joint inside: the space round the chamber is the water jacket. Bore a 16 mm hole in the top 100 mm off centre and seal in a short stainless tube a for the water. In one end bore 16 mm holes at the chamber's bottom and at the case's bottom and fit rubber stoppers: drains for the buttermilk and the water (ours). Make a hardwood lid for the mouth with a plug that fits it.
Materiais para este passo:
Tábua de madeira de lei4 peças
Filamento PETG1 peça
Cola de madeira1 peça
Parafusos para madeira40 peças
Tubo de aço inoxidável1 peça
Rolhas de borracha2 peçasFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra de mesa
Bússola
Tupia
Serra tico-tico
Conjunto de formões para madeira
Berbequim sem fios
Jogo de brocas
Conjunto de brocas de pá
Sargento de barra
Conjunto de chaves de fendas
Fita métrica6
6
Dasher: shaft D, bars b and strips c
Dasher: shaft D, bars b and strips c
Cut two hardwood end bars b 50 x 20 mm and 156 mm long, and bevel both ends of each across its width, from the full length on one edge to 100 mm on the other, the two bevels facing opposite ways. Cut six hardwood strips c 20 x 6 mm and 360 mm long, and screw three, one below another, along each pair of bevelled ends, so they stand on opposite sides of the shaft and run end to end across the corrugations. Bore the bars 16 mm at their middles, 360 mm apart over their outer faces, on a 16 mm stainless shaft D 515 mm long, and pin them. Pass the shaft through the ends at the chamber's centre, hold it with a shaft collar outside each end, and pin on a crank of mild steel flat bar, 120 mm throw, with a hardwood handle.
Materiais para este passo:
Tábua de madeira de lei1 peça
Parafusos para madeira12 peças
Varão de aço inoxidável1 peça
Contrapino2 peças
Shaft Collar2 peças
Barra chata de aço macio1 peça
Cavilhas de madeira dura1 peçaFerramentas necessárias:
Serra de mesa
Conjunto de formões para madeira
Berbequim sem fios
Jogo de brocas
Serra de arco para metais
Limas (lima de mão)
Torno de bancada
Conjunto de chaves de fendas7
7
The build in 3D
The build in 3D
FreeCAD model of this build, its front half cut away: the four printed rings with their spiral corrugations, set in the grooved case ends with the water jacket round them, the top with its mouth, lid and water tube a, the drains, and the dasher with its bevelled bars and strips on the cranked shaft.
8
8
Temper and churn
Temper and churn
Pour about 5 litres of heavy cream into the chamber, so its surface stays below the shaft. Pour water through the tube a into the jacket, warm in a cold room or cold in a warm one but never hotter than the hand can bear, until the cream reads about 15 °C on the thermometer. Put on the lid and turn the crank steadily, timing it. When the butter comes, draw the buttermilk off by its stopper into a bowl, take out the butter through the mouth, wash it in cold water until it runs clear, salt and weigh it. Drain the jacket by its stopper.
Materiais para este passo:
Natas para bater5 l
Água1 peça
Sal marinho grosso1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável9
9
Troubleshooting
Troubleshooting
Corrugated-chamber churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**David Sherman** of Uniontown, Maryland, and **Robert W. Fenwick** of Washington, D.C., US 29,445, 31 July 1860, "Churn", assigned to D. Sherman and Bernard Mills. They claimed "corrugating the surface of the near cylindrical churning chamber diagonally or spirally ... in combination with the blades c, c, (of the dasher) which are set so as to stand across the diagonal or spiral corrugations". Their chamber was a bent, corrugated metal plate; ours is printed rings with plain outsides. The drains are ours; the text does not say how the buttermilk or water is let off. The patent gives no sizes; every size here is ours.
Materiais
15- 4 peçasReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- 52 peçasReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- 2 peçasReferência
- 2 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
19- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
2Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Rocking-Churns Water-Jacket Churn: Two Small Churns Rock and Their Dashers Plunge, Wings Turn Above
por Buttercup
Marcenaria
10
0
0
0
0
0

Ring-Disk Spiral-Pin Churn: Cream Forced Out Between Corrugated Rings, Then Drawn to the Middle by Spiral Pins
por Buttercup
Marcenaria
4
0
0
0
0
0

Hot-Water Cylinder Churn: Cream Is Crushed Between a Warm Turning Cylinder and an Adjustable Plate, Then Falls to a Dasher
por Buttercup
Marcenaria
5
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

