Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Soldering Station: a Stand Whose Bimetal Switch Reads the Iron's Heat (Birk, Hart Mfg., US 2,248,486, 1941)
Ed

Criado por

Ed

3. novembro 2026FI
4
0
0
0
0

Soldering Station: a Stand Whose Bimetal Switch Reads the Iron's Heat (Birk, Hart Mfg., US 2,248,486, 1941)

A soldering station: an ordinary electric iron plugs into its stand, and the stand controls it. When the iron is laid in the stand's trough, its heater housing sits over a flue with a U-shaped bimetal switch inside; the heat it gives off opens the switch at the temperature you set with a screw, and closes it again as it cools. A red lamp shows the iron heating, a green lamp shows it hot and idling. Result: a stand that keeps an electric iron at a set temperature between jobs and shows its state. Source: H. W. Birk (Hart Manufacturing), US 2,248,486 (1941). Unknown: sizes, the bimetal, the lamps. Picture: the patent drawing.
Intermediário
Unknown

Instruções

1

Make the stand

Cast or form a box-shaped stand in one piece from a fire-resistant material such as porcelain: a high front wall, a low back wall, two side walls and a top sloping down about 10° toward the back, with feet at the corners so air can pass beneath. Close the bottom with a removable plate screwed to a flange and pierced with air holes. In the top, hollow a trough shaped to the iron's heater housing, ending at a shoulder, then a narrower groove for the tip. Cut a flue through the top along the trough, under a cover with holes. Ours: porcelain. Not given: sizes.

Materiais para este passo:

Material desconhecidoMaterial desconhecido1 porcelain stand
Metal desconhecidoMetal desconhecido1 bottom plate, screws

Ferramentas necessárias:

Dimensões desconhecidasDimensões desconhecidas
2

Fit the bimetal switch

Bend a strip of bimetal into a U whose legs spread apart when cool and close together when hot. Rivet one leg to a metal strip fixed beside the flue (on an insulating bracket if the stand conducts); put a contact on the free leg's end. Face it with a fixed contact on a screw stud threaded through a metal plate and out through the side wall in an insulating sleeve, slotted for a screwdriver: turning it sets the temperature, low for wax melting or high for electric branding irons. Not given: the bimetal, the contact metal.

Materiais para este passo:

Lâmina bimetálicaLâmina bimetálica1 peça
Metal desconhecidoMetal desconhecido1 strips, plate, contacts, stud
Material isolante desconhecidoMaterial isolante desconhecido1 bracket, sleeve, plate

Ferramentas necessárias:

Jogo de rebitarJogo de rebitar
Jogo de machos e cossinetesJogo de machos e cossinetes
3

Wire the outlet and lamps

Set an outlet in a side wall for the iron's plug, held by a flange and a split ring, and wire it in series with the switch to the supply cord. At the top of the front wall, set two lamp sockets at about 45°, one with a red lens and one with a green: wire the red in parallel with the iron's heater, the green in parallel with the switch. Not given: the lamp ratings, the outlet type.

Materiais para este passo:

Conector desconhecidoConector desconhecido1 outlet
Casquilho de lâmpadaCasquilho de lâmpada2 peças
LâmpadaLâmpada2 peças
Material desconhecidoMaterial desconhecido2 red and green lenses
Cabo flexível com fichaCabo flexível com ficha1 peça

Ferramentas necessárias:

Conjunto de chaves de fendasConjunto de chaves de fendas
4

Use it

Set the temperature by turning the slotted stud with a screwdriver. Plug an electric soldering iron into the stand's outlet and lay it in the trough so its heater housing closes the flue. While the bimetal is cool the switch is closed and the red lamp lights: the iron heats. At the set temperature the switch opens; the green lamp glows, the red goes dark and the iron idles. Lift the iron off and air rushes up the flue, cooling the bimetal so the iron heats again. Because it senses the heater, not the tip, the heater cannot burn out even if the tip is loose.

Materiais para este passo:

Ferro de soldarFerro de soldar1 electric soldering iron

Ferramentas necessárias:

Conjunto de chaves de fendasConjunto de chaves de fendas

Materiais

9

Ferramentas necessárias

4

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...