Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Spiral-Wing Spheroid Churn: A Ball Dasher on Balls Turns Freely on Its Rod, Its Spiral Wings Spinning It Each Stroke
Otis W. Stanford of Cincinnati received US 28,696, dated 12 June 1860, for a churn. On the foot of an ordinary up-and-down dash rod he hangs a round or egg-shaped wooden dasher that turns freely on balls, with spiral wings nearly touching the tub's sides. As the rod is worked, the cream spins the dasher one way then the other; the cream is squeezed between the wings and the wall, and air trapped under the round body is carried into it.
The patent gives no sizes; every size here is ours.
Intermediário
About 1 day, plus printing
Instruções
1
1
How far the dasher turns each stroke
How far the dasher turns each stroke
A carregar o notebook Jupyter…
2
2
A dash that turns as it is driven, one week before
A dash that turns as it is driven, one week before
Ross's pitched blades turn the dash and handle on a swivel. Stanford's spiral wings turn the dasher alone, on balls.
3
3
Read US 28,696
Read US 28,696
"The rod C being reciprocated, as in the common churn, the inertia of the fluid acts to swiftly rotate the dasher in successively opposite directions and this reacting upon the liquid imparts to the latter a quick succession of opposite vertical movements resulting in violent agitation."
4
4
Print the dasher's upper half
Print the dasher's upper half
Upper half of the spheroid, 150 mm across and 80 tall, with the upper halves of three spiral wings reaching 116 mm; bored 12.8 mm with a 32 mm recess for the upper ring of balls. PETG, 0.2 mm layers, 30 % infill, 4 walls.
5
5
Print the dasher's lower half
Print the dasher's lower half
Lower half, printed upside down, with the lower halves of the wings and the recess for the lower ring of balls. PETG, 0.2 mm layers, 30 % infill, 4 walls.
6
6
Lid B with boss b
Lid B with boss b
Turn a hardwood lid to fit the bucket's rim, 20 mm thick, with a boss 60 mm across and 140 mm tall in the middle, bored 26 mm through as the guide for the rod.
Materiais para este passo:
Tábua de madeira de lei1 peça
Cola de madeira1 peçaFerramentas necessárias:
Torno de madeira
Conjunto de brocas de pá
Berbequim sem fios
Lixa7
7
Rod C, dasher D, balls G, screw E and washer F
Rod C, dasher D, balls G, screw E and washer F
Cut a 25 mm hardwood rod 500 mm long and glue a 12 mm stainless spindle 170 mm long into its foot. Glue the two printed halves together with the wings lined up. Slide on a ring of 6 mm stainless balls in the upper recess, the dasher, and a second ring in the lower recess, and hold them with a stainless washer and a machine screw into the spindle's end. The dasher must spin freely.
Materiais para este passo:
Cavilhas de madeira dura1 peça
Varão de aço inoxidável1 peça
Cola de madeira1 peça
Rolamentos de esferas20 peças
Parafusos de máquina1 peça
Filamento PETG1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra de arco para metais
Limas (lima de mão)
Berbequim sem fios
Jogo de brocas
Conjunto de chaves de fendas8
8
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket and lid cut open: the rod through the boss, the spheroid dasher with its three spiral wings on its two rings of balls, held by the washer.
9
9
Churn
Churn
Pour about 6 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the dasher in and put on the lid over the rod. Work the rod up and down about 150 mm, steadily, timing it; the dasher turns one way and back. When the butter comes, lift the lid and dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater6 l
Sal marinho grosso1 peça
Água1 peça
Balde de 20 litros1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável10
10
Troubleshooting
Troubleshooting
Spiral-wing dasher churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Otis W. Stanford** of Cincinnati, Hamilton County, Ohio, US 28,696, 12 June 1860, "Churn". He claimed the upright tub with the reciprocating rod, the spheroidal dasher and spiral wings fitting the tub. His dasher is wooden; ours is printed in two halves, and the wings' number, twist and every size are ours.
Materiais
11- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 20 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
13- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
3Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Balance-Wheel Churn Frame: A Weighted Wheel Drives the Dash Up and Down and Its Pitched Blades Make It Revolve
por Buttercup
Marcenaria
5
0
0
0
0
0

Pendulum Churn: A Treadle Swings the Hung Churn, Arms From the Base Plunge the Dasher and a Twisted Strip Turns It
por Buttercup
Marcenaria
5
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

