Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Teapot: a Tinplate Picnic Teapot with Cock and Strainer (Hasluck, 1907)
A square tinplate teapot from a picnic outfit: folded from one blank, with a hinged lid, and a cock at the bottom behind a perforated strainer that holds back the leaves.
Blank 1 ft 4 1/4 in by 1 ft 0 3/8 in; lid 4 1/8 by 4 in.
Source: Paul N. Hasluck, Tinplate Work (1907), pp. 37-39. Unknown: folding order, solder, the cock. Picture: Figs. 96-97 of the book.
Intermediário
Unknown
Instruções
1
1
Cut the body blank
Cut the body blank
Cut a piece of tin 1 ft 4 1/4 in long by 1 ft 0 3/8 in wide and mark the pattern of Fig. 96 on it, with the hole for the cock tube. Not given: the folding order. Ours: bend it up on the dotted lines and solder the seams.
Materiais para este passo:
Chapa de folha de flandres1 body
Solda de estanho-chumbo1 peçaFerramentas necessárias:
Ponta de traçar
Tesoura de chapa
Estaca
Maço de madeira
Ferro de solda elétrico
Fluxo2
2
Fit the cock and strainer
Fit the cock and strainer
Solder a tube about 1/2 in long into the hole for the cock (Fig. 97) and fit the cock to it. Develop the strainer (Fig. 98): top curve radius 1 13/16 in, chord corner to corner 2 15/16 in. Perforate it and solder it across the corner in front of the tube (Fig. 99).
Materiais para este passo:
Tubo de latão1 1/2 in
Torneira de descarga1 peça
Chapa de folha de flandres1 strainer
Solda de estanho-chumbo1 peçaFerramentas necessárias:
Compasso de pontas
Tesoura de chapa
Puncionador de furos para chapa
Bloco de madeira dura
Ferro de solda elétrico
Fluxo3
3
Make the hinged lid
Make the hinged lid
Cut the lid (Fig. 100) 4 1/8 by 4 in; the inner rectangle 3 1/2 by 3 1/2 in leaves 1/4 in to bend up. Cut hinge projections 1/2 in wide by 5/8 in deep with equal spaces, the outer ones only 1/4 in wide. Bend them round a wire 1/16 in thick. Hasluck adds that the teapot may be enamelled dark green.
Materiais para este passo:
Chapa de folha de flandres1 lid
Arame de ferro1 1/16 inFerramentas necessárias:
Tesoura de chapa
Estaca
Maço de madeiraMateriais
5- Referência
- 2 peçasReferência
- 1 1/2 inReferência
- 1 peçaReferência
- 1 1/16 inReferência
Materiais de Blueprints conectados
Este projeto faz
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.


