ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
The Oil-Wick Fountain Brush: A Can Whose Wick Is the Brush
Woody

Criado por

Woody

6. outubro 2026NO
4
0
0
0
0

The Oil-Wick Fountain Brush: A Can Whose Wick Is the Brush

An oil can and a rag spill, and a brush dipped in oil drips. Preston H. Clingan of Florence, Colorado, received US 787,278, dated 11 April 1905, for "a can of very simple form which is so constructed as to prevent the possibility of spilling the contents thereof": an open thimble hangs from the can's mouth to near its bottom, a rolled burlap wick inside it is frayed above the mouth into a brush, and oil in the chamber round the thimble reaches the wick from underneath. This rung works out how high a wick can lift oil, then builds the can from a jar, a tin and burlap and weighs the oil it lays on a board.
Iniciante
About 2 hours

Instruções

1

How high the wick lifts

A carregar o notebook Jupyter…
2

A wick that feeds oil before it

The embedded blueprint feeds oil to a bearing through a wick. Clingan turns the wick's frayed end into the brush.
3

Read US 787,278

"My object is to provide a can of very simple form which is so constructed as to prevent the possibility of spilling the contents thereof. The can includes a wick of absorbent material, which is constantly supplied with oil or other fluid within the can."
4

Make the thimble

Remove both ends of a tin can that passes through the jar's mouth with 6 mm to spare. Cut it 10 mm shorter than the jar's inside height. File the cut edges.

Materiais para este passo:

LataLata1 peça

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Limas (lima de mão)Limas (lima de mão)
RéguaRégua
Luvas de trabalho em couroLuvas de trabalho em couro
5

Cut the lip ring

Cut an aluminium ring: outside to fit inside the jar's mouth, inside to fit round the thimble. Drill it 3 mm for a filling screw.

Materiais para este passo:

Chapa de alumínioChapa de alumínio1 peça

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Limas (lima de mão)Limas (lima de mão)
6

Fix the thimble

Epoxy the ring round the thimble's top and into the jar's mouth, the thimble hanging 10 mm clear of the floor. Cut a rubber washer for the filling screw.

Materiais para este passo:

Frasco de vidroFrasco de vidro1 peça
Epóxi de dois componentesEpóxi de dois componentes1 peça
Parafusos de máquinaParafusos de máquina1 peça
Chapa de borrachaChapa de borracha1 peça

Ferramentas necessárias:

X-ato (faca de precisão)X-ato (faca de precisão)
Conjunto de chaves de fendasConjunto de chaves de fendas
7

Roll the wick

Roll a strip of burlap tightly until it fills the thimble, 15 mm longer than it. Push it in and fray the top 15 mm with the fingers.

Materiais para este passo:

Aniagem / serapilheiraAniagem / serapilheira1 peça

Ferramentas necessárias:

TesouraTesoura
RéguaRégua
8

The build in 3D

FreeCAD model of this build, not of the patent: a 90 mm jar with a 66 mm mouth, the aluminium lip ring and filling screw, a 53 mm thimble 10 mm off the floor, the burlap wick with its frayed top, and the lid.
Arquivo de designBLENDCC0 - Free
9

Oil a board and weigh it

Pour linseed oil through the filling hole to half the jar's height and wait until the wick's top darkens. Weigh a plywood board, brush it once over, and weigh it again. Turn the closed jar on its side over a rag for a minute.
Passo 9 - Image 1

Materiais para este passo:

Óleo de linhaça cozidoÓleo de linhaça cozido1 peça
Placa de contraplacadoPlaca de contraplacado1 peça
Trapos de algodãoTrapos de algodão1 peça

Ferramentas necessárias:

Balança digital de cozinhaBalança digital de cozinha
CronómetroCronómetro
Fita métricaFita métrica
10

A wick that stays dry, floods or leaks

Oil-wick fountain brush troubleshooting.

Flow

Loading...
11

History and honest limits

**Preston H. Clingan** of Florence, Colorado, assignor of one-half to John H. Todd of Cañon City, filed US 787,278 on 28 July 1904; it is dated 11 April 1905. His can is cylindrical with both ends contracted and threaded, so the cover fits either end; the thimble is soldered to an inward lip at the mouth; the wick is preferably a roll of burlap. He named oiling or polishing surfaces and cleaning windows among its uses. **Honest limits.** A jar with one threaded mouth stands in for his can. The notebook assumes a fully wetting wick and one pore size. Your weights are the result.

Materiais

10

Ferramentas necessárias

12

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...