Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
V-Slide Tubing Cutter: Two Slide Halves Held on the Ways by One Spring Clip, a Reamer on the Frame (Thewes, 1938)
Forge

Criado por

Forge

13. novembro 2026NO
12
0
0
0
0

V-Slide Tubing Cutter: Two Slide Halves Held on the Ways by One Spring Clip, a Reamer on the Frame (Thewes, 1938)

William O. Thewes of North Ridgeville, Ohio, received US 2,130,934, dated 20 September 1938 and assigned to The Ridge Tool Company, for a cutter for thin copper and brass tubing. A C-frame carries a cutting wheel at one end and a feed screw at the other. The screw pushes a V-slide that holds the tube against the wheel. The slide is two halves on ways along the frame, held together by one V-shaped spring clip, which is also the face the tube bears on. A triangular reamer on the side of the frame cleans the cut end, and the frame is its handle. We saw the frame from steel plate and pin the reamer in. His parts were die cast. All sizes are ours.
Intermediário
About 3 days

Instruções

1

Where the tube sits

A carregar o notebook Jupyter…
2

Read US 2,130,934

"With my improved cutter the ways or guides are integral with the frame and are uninterrupted throughout the length of the frame, and the slide is held in close sliding engagement on the ways without the use of bolts or rivets."
3

Print the template

Frame, slide half, end section, reamer and clip blank at 1:1 on A4, with the 8 and 28 mm tubes drawn in. print at 100 % (check the 50 mm bar).
Arquivo de designPDFCC0 - Free
4

Saw out the frame

Glue the frame outline on 16 mm plate. Drill a row of holes inside the C, saw to them, and file to the line. Saw the 7 mm wheel slot down through the wheel post with two cuts, break out the middle and file it flat. Drill the 5 mm wheel pin and 4 mm tie pin holes across the slot. Drill 8.5 mm along the screw axis through the other post and tap it M10.

Materiais para este passo:

Chapa grossa de aço macioChapa grossa de aço macio1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de limasJogo de limas
Engenho de furarEngenho de furar
Morsa de máquinaMorsa de máquina
Jogo de brocasJogo de brocas
Jogo de machos e cossinetesJogo de machos e cossinetes
Punção de centroPunção de centro
Ponta de traçarPonta de traçar
Torno de bancadaTorno de bancada
Óleo de corteÓleo de corte
5

File the ways

Along the bottom bar, between the posts, file a groove 2 mm deep and 4 mm high in both faces, 3 mm below the top edge. This leaves a T-shaped rib along the top: the ways. Keep it straight and the same all along, so the slide runs smoothly from end to end.

Ferramentas necessárias:

Jogo de limasJogo de limas
Jogo de limas de agulhaJogo de limas de agulha
Torno de bancadaTorno de bancada
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
6

Turn the cutting wheel

Chuck a tool steel bar and face it. Turn the end to 20 mm across for 10 mm, centre drill and drill a 5 mm hole 10 mm deep, and turn the edge to a 50 degree vee, 25 degrees each side, sharp in the middle of the 6 mm width. Part it off 6 mm long and take the burr off the hole.

Materiais para este passo:

Barra de aço-ferramentaBarra de aço-ferramenta1 peça

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Goiva de sangrarGoiva de sangrar
Conjunto de brocas de centrarConjunto de brocas de centrar
Jogo de brocasJogo de brocas
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
Óculos de segurançaÓculos de segurança
7

Make the reamer

Saw a triangle with 22 mm sides from 3 mm flat tool steel and drill its 4 mm hole. Grind each edge to a 60 degree bevel from both sides, so all three edges cut. Saw a 3 mm wide slot, 22 mm long and 8 mm deep, in the middle of the frame's bottom edge, 50 mm from the wheel end, and drill the 4 mm pin hole across it.

Materiais para este passo:

Barra chata de aço para ferramentasBarra chata de aço para ferramentas1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Esmeriladora de bancadaEsmeriladora de bancada
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Jogo de limasJogo de limas
Óculos de segurançaÓculos de segurança
8

Harden and temper

Heat the wheel and the reamer to a cherry red, until a magnet no longer sticks, and quench it in water, moving it about. Rub it bright with a stone, warm it on a piece of steel plate over the fire, and quench again as soon as it turns a light straw colour.

Ferramentas necessárias:

ForjaForja
Tenaz de forjaTenaz de forja
Íman pequenoÍman pequeno
Balde de têmperaBalde de têmpera
ÁguaÁgua
Pedra de amolarPedra de amolar
Luvas de soldadorLuvas de soldador
Óculos de segurançaÓculos de segurança
9

Make the slide halves

Saw two pieces of 10 mm plate to the slide outline, one the mirror of the other, and file the V. On the inner face of each, saw and file a pocket for half the screw head and a slot for its neck. Saw and file a step along the bottom edge of each half so its lip fits the groove under the ways (end section on the template). File a shallow notch in the outer face of each half, beside the V, for the clip's tongues.

Materiais para este passo:

Chapa grossa de aço macioChapa grossa de aço macio1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de limasJogo de limas
Jogo de limas de agulhaJogo de limas de agulha
Torno de bancadaTorno de bancada
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
Ponta de traçarPonta de traçar
10

Bend the V clip

Cut the clip blank from 0.5 mm spring steel strip. Bend the four tongues up at right angles, then fold the blank to 90 degrees on the dashed line, over the slide's V.

Materiais para este passo:

Fita de aço-molaFita de aço-mola1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de limasJogo de limas
Torno de bancadaTorno de bancada
Martelo de bolaMartelo de bola
11

Make the feed screw

Cut 120 mm of M10 threaded rod. Chuck it and turn the end to a 9 mm head 4 mm long on a 6 mm neck 3 mm long. Drill a 6 mm hole across the other end and push a 70 mm piece of 6 mm rod through it for the T-handle. Peen it both sides so it stays put.

Materiais para este passo:

Varão roscadoVarão roscado1 peça
Varão de aço macioVarão de aço macio1 peça

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Goiva de sangrarGoiva de sangrar
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Martelo de bolaMartelo de bola
Serra de arco para metaisSerra de arco para metais
12

Assemble

Fit the wheel in its slot with the 5 mm pin, and the 4 mm tie pin above it, peened. Tap the reamer into its slot and pin it. Screw the feed screw through the boss. Put the halves on the ways from the sides, closing them round the screw head, and spring the clip over their V so its tongues snap into the notches. Oil the ways and the screw.

Materiais para este passo:

Pino cilíndrico de açoPino cilíndrico de aço3 peças

Ferramentas necessárias:

Martelo de bolaMartelo de bola
Punção de centroPunção de centro
Torno de bancadaTorno de bancada
Óleo de corteÓleo de corte
13

Cut a copper tube

Mark a copper tube and hold it in a vice with soft jaws, or by hand for small tubes. Open the screw, drop the cutter over the tube, and screw the slide in until the wheel just touches. Turn the cutter once round, give the screw about a quarter turn, and go on until the tube parts. The wheel should run in its own groove; the end should be square and not squeezed oval. Clean the inside of the end with a deburring tool.

Materiais para este passo:

Tubo de cobreTubo de cobre1 peça

Ferramentas necessárias:

Torno de bancadaTorno de bancada
Rebarbador manualRebarbador manual
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
14

Ream the end

Hold the frame like a T-handle, put the reamer's point in the cut end, and turn it a few times to take off the fin the wheel has turned in.

Ferramentas necessárias:

Torno de bancadaTorno de bancada
15

Troubleshooting

Tubing cutter troubleshooting.

Flow

Loading...
16

History and honest limits

**William O. Thewes** of North Ridgeville, Ohio, US 2,130,934, dated 20 September 1938, filed 4 November 1935, assigned to The Ridge Tool Company. Earlier slides needed notched ways, which weaken the frame, or bolts that come loose; he claimed "a V block reciprocable on the guideway and comprising two sections, and a face plate clamping said sections together". A later certificate corrects "same" to "frame" and "base" to "boss". His frame and slide were die cast and the reamer cast into the frame; ours are sawn from plate and the reamer is pinned. The patent gives no sizes; all of ours are ours.

Materiais

8

Ferramentas necessárias

28

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...