Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Thompson (Nlaka'pamux) Summer Mat Lodge: Paired Poles Tied with Willow, Cross-Poles, Overlapping Reed Mats to an Open Smoke Gap (Teit, 1900)
The Thompson (Nlaka'pamux) summer house from James Teit: two pairs of poles tied with willow and set about 10 ft apart as gables, joined by cross-poles, short poles leaning in at the ends, and rows of 5 x 12 ft reed mats lapped like shingles up to a smoke gap about 3 ft below the top; or a round lodge of a dozen poles meeting at the top. Lived in for all but the three coldest months.
Iniciante
Half a day
Instruções
1
1
His measures
His measures
A carregar o notebook Jupyter…
2
2
Read Teit
Read Teit
"The construction of either kind was very simple."
3
3
Set the gables
Set the gables
Clear a flat piece of ground. Tie two pairs of stout poles together at their small ends with willow withes and set them up about 10 ft (3 m) apart as the two gable ends.
Materiais para este passo:
Vara de madeira1 peça
Vime de salgueiro1 peçaFerramentas necessárias:
Machado
Faca4
4
Tie the frame
Tie the frame
Tie three or four horizontal cross-poles along each side from pair to pair, and sometimes two or three poles parallel to the pairs. Close the gables with several short poles leaning their tops against the main poles, leaving a doorway in one gable end.
Materiais para este passo:
Vara de madeira1 peça
Vime de salgueiro1 peçaFerramentas necessárias:
Faca5
5
Mat it
Mat it
Lay long reed mats (about 5 x 12 ft, 1.5 x 3.7 m) round the bottom of the frame, then another row slightly overlapping above, and so on to within about 3 ft (90 cm) of the top. Leave the top open for smoke and light. Bank earth half a foot up round the bottom if you like; two or three layers of mats for cold.
Materiais para este passo:
Esteira de canas1 peça
Cordame1 peçaFerramentas necessárias:
Pá6
6
Door, flap and floor
Door, flap and floor
Leave a doorway of about 3 x 5 ft or less in the lowest row and hang a mat, skin or blanket over it, a little larger, stiffened at the bottom with a thin stick. Make a flap of mat on a long slender pole to cover the smoke hole at night and in rain. Strew the floor with small fir branches, thicker by the walls where people sleep; the fire goes in the middle.
Materiais para este passo:
Esteira de canas1 peça
Cavilha de madeira1 peça
Feno1 peçaFerramentas necessárias:
Faca7
7
Troubleshooting
Troubleshooting
Mat lodge troubleshooting.
Flow
Loading...
8
8
History and honest limits
History and honest limits
From James Teit, *The Thompson Indians of British Columbia*, **Memoirs of the American Museum of Natural History, Jesup North Pacific Expedition** vol. I part IV (1900), pp. 195-197 and Figs. 137-142 (checked on the archive.org scan cihm_16242). Round lodges, 15-20 ft across, were built of a dozen or more poles leaning together unfastened; the Nicola and Spences Bridge bands often used painted skins instead of mats, and where bark was plentiful, strips of spruce, fir or pine bark. In the materials list hay stands in for fir branches (no head yet); pole sizes are ours.
Materiais
6- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
Este projeto faz
Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Thompson (Nlaka'pamux) Tule Mat: Dogbane Fibre Cleaned on a Board Edge, Thigh-Spun, Reeds Strung Across (Teit, 1900)
por Tex
Têxtil e Couro
2
0
0
0
0
0

Thompson (Nlaka'pamux) Winter Pit House: Circle Laid Out with Two Crossed Ropes, Four Rafters on Braces, Earth-Covered, Notched-Log Ladder (Teit, 1900)
por Woody
Marcenaria
4
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.
