Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Counter-Revolving Dasher Churn: Geared Dashers on Offset Shafts Turn Contrary Ways, Their Blades Skewed Contrary Ways
Aaron C. Vaughan of Johnstown, Pennsylvania, received US 27,396, dated 6 March 1860, for churn dashers. Two or more revolving dashers stand end to end in one box on parallel shafts set a little out of line, joined by pinions inside the box so each turns contrary to the next; the blades of each are inclined contrary to the next's. He says the cream then neither whirls round the shafts nor runs to one end.
This builds his two-dasher form (Fig. 1). The patent gives no sizes; every size here is ours.
Avançado
About 2 days, plus printing
Instruções
1
1
Two dashers, one crank
Two dashers, one crank
A carregar o notebook Jupyter…
2
2
Two parts turning contrary ways, three weeks before
Two parts turning contrary ways, three weeks before
Ward turns a cylinder against its dashers. Vaughan turns dasher against dasher, side by side in one box.
3
3
Read US 27,396
Read US 27,396
"If straight the force of the current would be around the shaft, but this is counteracted by breaking the line of the shaft, though still keeping them parallel with each other. If the blades were inclined in one direction only, then the cream would be forced to that end of the box toward which the inclination tends."
4
4
Print the pinions a, a
Print the pinions a, a
Spur pinion, module 2.5, 20 teeth, 18 mm wide, with a hub 28 mm across; bored 16.4 mm for the shaft. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Box A, pillar block E and lid
Box A, pillar block E and lid
From 20 mm hardwood board make a box 700 x 300 mm inside and 300 deep; glue and screw it, and seal the inside joints with silicone sealant. Screw a hardwood pillar block E, 30 x 120 mm and 180 high, upright across the floor's middle, 340 mm from the crank end. Bore it 16.6 mm across at two points 150 mm up, 25 mm either side of the middle. Bore the crank end 17 mm across 150 mm up and 25 mm to one side, for dasher B; bore the other end 16 mm for the set screw b, 25 mm to the other side. Cut a lid to lie on top.
Materiais para este passo:
Tábua de madeira de lei3 peças
Cola de madeira1 peça
Parafusos para madeira40 peçasFerramentas necessárias:
Serra de mesa
Berbequim sem fios
Jogo de brocas
Sargento de barra
Conjunto de chaves de fendas
Fita métrica
Lixa6
6
Dashers B and C
Dashers B and C
For each dasher cut four hardwood blades 240 x 40 x 8 mm, two hardwood hubs 36 mm across and 24 long bored 16.4 mm, and eight 12 mm dowel arms. Glue four arms into each hub a quarter turn apart, 220 mm apart along the shaft, and screw the blades across their ends 100 mm from the shaft, each blade skewed 8 degrees to the shaft (one end 31 mm ahead of the other). Skew dasher B's blades one way and C's the other.
Materiais para este passo:
Tábua de madeira de lei1 peça
Cavilhas de madeira dura1 peça
Cola de madeira1 peça
Parafusos para madeira16 peçasFerramentas necessárias:
Serra de mesa
Berbequim sem fios
Jogo de brocas
Serra de arco para metais
Sargento de barra
Conjunto de chaves de fendas
Lixa7
7
Shafts, pinions a, a and set screw b
Shafts, pinions a, a and set screw b
Cut a 16 mm stainless shaft 440 mm long for B: through the crank end, through dasher B and its pinion, into the pillar block. Cut one 386 mm long for C: its pinion in line with B's beside the block, through the block and dasher C, its far end in the set screw's step. The pinions mesh 50 mm apart; pin each to its shaft. For the set screw b cut 90 mm of M16 threaded rod, drill a 16.6 mm step 20 mm deep in its inner end, run it through two nuts either side of the end wall, and fix a hardwood handle on its outer end; screw it in until C turns freely without end play. Fit a hardwood crank 120 mm long with a dowel handle on B's outer end.
Materiais para este passo:
Varão de aço inoxidável2 peças
Filamento PETG1 peça
Varão roscado1 peça
Porca sextavada2 peças
Shaft Collar2 peças
Contrapino2 peças
Tábua de madeira de lei1 peça
Cavilhas de madeira dura1 peça
Cola de madeira1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra de arco para metais
Limas (lima de mão)
Torno de bancada
Berbequim sem fios
Jogo de brocas
Chave inglesa ajustável8
8
The build in 3D
The build in 3D
FreeCAD model of this build, one side and the lid left off: dasher B on its shaft from the crank end to the pillar block E, dasher C on the offset shaft from E to the set screw b, and the two pinions a meshing beside E.
9
9
Churn
Churn
Pour in about 15 litres of heavy cream at about 15 °C, checked with the thermometer, put on the lid and turn the crank steadily, timing it: the two dashers turn contrary ways. When the butter comes, lift the lid and the butter out, ladle or tip the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater15 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável10
10
Troubleshooting
Troubleshooting
Counter-revolving dasher churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Aaron C. Vaughan** of Johnstown, Cambria County, Pennsylvania, US 27,396, 6 March 1860, "Churn-Dasher". He did not claim two or more dashers in one churn, nor turning them contrary ways by gearing, but the series of dashers set lengthwise, geared inside the box, each pair turning contrary ways with blades inclined contrary ways; his Fig. 2 shows three. He does not say how the contrary inclination is measured; ours are mirror images. The patent gives no sizes; every size here is ours, and our pinions are printed.
Materiais
14- 3 peçasReferência
- 3 peçasReferência
- 56 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 2 peçasReferência
- 2 peçasReferência
- 2 peçasReferência
- 15 lReferência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
16- 1 vendor sell this, none ship to you yetReferência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
2Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Counter-Turning Cylinder Churn: The Ribbed Cylinder Turns One Way While the Dashers Inside Turn the Other
por Buttercup
Marcenaria
6
0
0
0
0
0

Contrary Hinged-Dasher Air-Pump Churn: Two Crossing Dashers Fold to Gather, a Pump Blows Air Through the Cream
por Buttercup
COMIDA E BEBIDAS
4
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

