ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Vegetable Peeler: a Swivel Blade with a Guide Rod on a Bent Strip Handle (after De Vault, 1938)
Forge

Criado por

Forge

22. novembro 2026NO
0
0
0
0
0

Vegetable Peeler: a Swivel Blade with a Guide Rod on a Bent Strip Handle (after De Vault, 1938)

A swivel peeler you make from steel strip and wire: a narrow hardened blade with a guide rod in front of it swings on two pins between the legs of a bent stainless handle, so it follows the shape of a potato or carrot and takes off an even, thin peel. A small hooked blade on the side cuts out eyes. Ralph De Vault patented this design in 1938.
Intermediário
About 5 hours

Instruções

1

How a swivel peeler is used

Swivel and Y peelers tested on potatoes, carrots and squash (America's Test Kitchen). Ours is a swivel peeler.
2

De Vault's peeler, 1938

US 2,106,796: a narrow blade 10 and a guide rod 11 are joined by end walls and swing on pins 9 between the legs 5 of a handle bent from strip. The pivot lies between the edge and the rod, so the pull goes straight through the edge and the blade neither digs in nor lifts. Rivet 14's head stops the swing; blade 12 cuts out eyes. We build this form (Figs. 1-4).
Passo 2 - Image 1
3

Where the holes go

A carregar o notebook Jupyter…

Ferramentas necessárias:

Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
4

Print the drawing

Blade blank, eye trimmer and the end of a handle leg at 1:1, with an enlarged end view. Print at 100 % and check the 50 x 10 mm box.
Arquivo de designPDFCC0 - Free
5

Cut and drill the handle strip

Saw a strip 12 x 295 mm from 1.5 mm stainless sheet and file the edges smooth. Lay the 1:1 leg end on each end and punch the hole centres through the paper: pivot, brace, and holes 14 and 15 at one end only. Drill the pivots 2.2 mm, the others 2 mm. File the corner of each end away, 7.3 mm along the top and 4.4 mm down.

Materiais para este passo:

Chapa de aço inoxidávelChapa de aço inoxidável1 piece (1.5 mm, 12 x 295 mm strip)

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Lima para metalLima para metal
Punção de centroPunção de centro
Jogo de brocasJogo de brocas
Engenho de furarEngenho de furar
Torno de bancadaTorno de bancada
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
6

Bend the handle

Bend the middle 107 mm round something about 68 mm across (a can or pipe) into a half circle, with the 12 mm side upright. From each end leave 43 mm straight, then bend an S outwards (two bends of about 57 degrees round a 20 mm bar) so the legs end parallel, 48.2 mm apart inside and the holes facing each other.

Ferramentas necessárias:

Torno de bancadaTorno de bancada
Alicate de bico chatoAlicate de bico chato
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
7

Cut the blade and the trimmer

If the carbon steel strip springs back when bent, soften it first: heat it to a dull red and let it cool slowly. Cut the blade blank and the eye trimmer to the drawing, punch and drill the 2 mm holes while flat, and file the edges. Fold each paddle 90 degrees in the vise on the dashed line, both to the same side, so the paddles stand square and face each other.

Materiais para este passo:

Fita de aço-carbonoFita de aço-carbono1 piece (0.6 mm, 60 x 40 mm)

Ferramentas necessárias:

Maçarico a propanoMaçarico a propano
Tesoura de chapaTesoura de chapa
Punção de centroPunção de centro
Jogo de brocasJogo de brocas
Jogo de limas de agulhaJogo de limas de agulha
Torno de bancadaTorno de bancada
Alicate de bico chatoAlicate de bico chato
8

Bevel, harden and temper

File a bevel about 1.5 mm wide on the blade's top face down to the edge, and file the trimmer's point and curved edge. Heat each part evenly to the point where a magnet no longer sticks, quench it in warm cooking oil, then clean it bright with emery. Temper both in the oven at 200 degrees C for one hour (light straw).

Ferramentas necessárias:

Lima para metalLima para metal
Maçarico a propanoMaçarico a propano
Íman pequenoÍman pequeno
Balde de têmperaBalde de têmpera
Óleo alimentarÓleo alimentar
Lixa de esmerilLixa de esmeril
FornoForno
Termómetro de fornoTermómetro de forno
Luvas resistentes ao calorLuvas resistentes ao calor
Óculos de segurançaÓculos de segurança
9

Fit the guide rod and pins

Cut 2 mm stainless wire: one guide rod 48 mm long and two pins 5 mm long. Push the rod through both rod holes and peen each end to a small head no more than 1.3 mm high. Put a pin through each pivot hole from inside, peen the inside end to a head, and leave about 3.5 mm sticking out.

Materiais para este passo:

Arame de aço inoxidávelArame de aço inoxidável1 piece (2 mm, 60 mm)

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Martelo de bolaMartelo de bola
Torno de bancadaTorno de bancada
Lima para metalLima para metal
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
10

Assemble

Spring the legs apart and let the pins drop into the pivot holes, the guide rod towards the loop. Rivet the trimmer on the outside of its leg with two 2 mm wire rivets, leaving rivet 14 with a full 1 mm head inside the leg: it stops the swing. Last, fit the brace: 3 mm rod with 2 mm stubs filed on the ends, so the shoulders hold the legs 48.2 mm apart; peen the ends.

Materiais para este passo:

Arame de aço inoxidávelArame de aço inoxidável1 piece (2 mm, 15 mm, two rivets)
Varão de aço inoxidávelVarão de aço inoxidável1 piece (3 mm, 55 mm)

Ferramentas necessárias:

Martelo de bolaMartelo de bola
Lima para metalLima para metal
Torno de bancadaTorno de bancada
Serra de arco para metaisSerra de arco para metais
11

Sharpen and peel

Hone the bevel on the stone and take the burr off the flat face. Hold the loop and draw the peeler towards you over a potato, guide rod first: the blade tilts by itself to follow the surface. Wash, dry and oil the blade after use.

Materiais para este passo:

Óleo mineral de uso alimentarÓleo mineral de uso alimentar2 ml

Ferramentas necessárias:

Pedra de amolarPedra de amolar
12

Troubleshooting

Peeler problems and fixes.

Flow

Loading...
13

History and honest limits

Ralph P. De Vault, South Pasadena, Calif.: US 2,106,796, "Peeler", filed 26 March 1935, granted 1 February 1938. The 22 1/2 degrees and the one-third pivot are from his second form (Figs. 5-7, a stamped cutter on a round-bar handle); we use them on his strip form. Ours: every size, the steels, the folded paddles and the heat treatment. Not made by us yet.

Materiais

5

Ferramentas necessárias

21

Ficheiros de design

1

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...