Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Wedge-Disk Rotary Churn: A Geared Disk With Wedge Teeth Throws Cream Up Into a Collar, Slanted Holes Let the Milk Back Out
Buttercup

Criado por

Buttercup

11. novembro 2026IE
8
0
0
0
0

Wedge-Disk Rotary Churn: A Geared Disk With Wedge Teeth Throws Cream Up Into a Collar, Slanted Holes Let the Milk Back Out

D. T. Ward of Mansfield, Ohio, received US 30,941, dated 18 December 1860, for a square box churn whose upright staff is spun by a crank and toothed wheels. At its foot a disk with a ring of wedge-shaped teeth cuts the cream and throws it up into a wide collar on the disk; slanted holes through the disk let the milk run back out, so a current flows through the collar while the butter gathers inside it. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

The disk's speed

A carregar o notebook Jupyter…
2

A geared spinning dasher, two months before

Kellberg's wings throw the cream outward against a fixed disk. Ward's teeth throw it upward into a collar that holds the butter.
3

Read US 30,941

"When this disk and rim, or collar are revolved rapidly the milk is cut and agitated by the projections on the disk, and also is given an upward tendency by them. It is thrown into the collar D, and passes out at the openings s, s, s. Thus a constant stream or current is produced from the out to the inside of the collar and vice versa. The butter remains and is gathered in the collar while the milk as has been stated passes out at the openings s, s, s."
4

Box A and lid

Glue up a square hardwood box A 300 x 300 mm inside and 400 deep, sides and bottom 22 mm, joints sealed with silicone sealant. Cut a 12 mm HDPE lid to the outside, 344 mm square, with a 32 mm hole at the centre.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei3 peças
Cola de madeiraCola de madeira1 peça
Vedante de siliconeVedante de silicone1 peça
Parafusos para madeiraParafusos para madeira24 peças
Chapa de PEADChapa de PEAD1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
5

Print the step

The step on the box's floor: 60 mm across, 15 high, with a 10.6 mm hole 9 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Print the disk C and collar D

Disk C and collar D in one: a 160 mm disk with a ring of twelve wedge teeth to 220 mm across, each full depth at its leading edge and sloping to nothing at its trailing edge, four 18 mm holes s slanting 40 degrees the other way, and the collar 150 mm across and 60 high on top; 28.4 mm bore. Needs a 230 mm bed. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
7

Print the wheel F

The toothed wheel F on the staff's top: 14 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
8

Print the wheel E

The toothed wheel E on the crank shaft H: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
9

Staff B

Turn a hardwood staff B 28 mm across and 400 mm long. Set a 10 mm stainless pin 14 mm out of its foot and a 16 mm stainless rod 90 mm long 20 mm into its top. Slide the disk C on so its underside is 10 mm above the staff's wooden foot, and pin it with a dowel through its hub.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável2 peças
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Torno de madeiraTorno de madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
10

Upright G, arm d, standard a, shaft H and crank

Cut a hardwood upright G 40 x 40 mm and 295 mm long, with two slots 10 mm wide and 40 long through it, and fix it upright on the middle of the box's back with two carriage bolts, washers and wing nuts, so it can be raised or lowered to set the wheels' mesh. Glue and screw a hardwood arm d 50 x 25 mm, 332 mm long, across its top, reaching over the box's centre, bored 16.6 mm there for the staff. Screw two hardwood bearing blocks 50 x 25 x 108 mm on the arm, one 60 to 85 mm in front of the staff (the standard a) and one 25 to 50 mm behind it, bored 16.6 mm across 83 mm up. Stand the staff on the step through the lid and arm, pin the wheel F on its top, run a 16 mm stainless shaft H 180 mm long through the blocks with the wheel E pinned on it meshing F, a shaft collar, and a crank of mild steel flat bar, 100 mm throw, with a hardwood handle.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Parafuso de carroçariaParafuso de carroçaria2 peças
Porca borboletaPorca borboleta2 peças
Anilha planaAnilha plana2 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira8 peças
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Shaft CollarShaft Collar1 peça
ContrapinoContrapino3 peças
Barra chata de aço macioBarra chata de aço macio1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de mesaSerra de mesa
Conjunto de formões para madeiraConjunto de formões para madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Chave inglesa ajustávelChave inglesa ajustável
Conjunto de chaves de fendasConjunto de chaves de fendas
11

The build in 3D

FreeCAD model of this build, the box cut open: the step, the staff with the wedge-toothed disk and its collar, the lid, and the upright G with arm d, the bearing blocks, the crank shaft, the two toothed wheels and the crank.
Arquivo de designBLENDCC0 - Free
12

Churn

Pour about 12 litres of heavy cream at about 15 °C, checked with the thermometer, into the box so it stands over the collar, put on the lid and set the wheels' mesh with the upright G. Turn the crank briskly, timing it. When the butter comes, much of it lies in the collar. Lift out the staff and disk, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater12 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
13

Troubleshooting

Wedge-disk churn troubleshooting.

Flow

Loading...
14

History and honest limits

**D. T. Ward** of Mansfield, Richland County, Ohio, US 30,941, 18 December 1860, "Churn". He claimed "the disk or wheel C, constructed as described and in connection therewith the rim or collar D", and said currents had been made before. He does not give the number of teeth or holes, or the form of his toothed wheels; ours are 12 teeth, four round holes and a printed crown wheel and pinion. His upright G had a diagonal brace; ours is bolted through slots so it can be raised or lowered. Every size here is ours.

Materiais

17

Ferramentas necessárias

19

Ficheiros de design

5

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...